Wheel studs > me.

[LTb1ow]

I have the worst luck it seems...

Ran Adam's wheels, so they had the shank style lug,and I have three inch ARP wheel studs... well, gonna need a new one now..
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs443.ash2/71679_1614253752246_1113366798_1772655_5584207_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs796.snc4/67658_1614257872349_1113366798_1772658_4600764_n.j pg

Big thanks to that nameless racer who helped us out. :nod:

Dunno what happened, went to switch back to 17 inch rims cause the 28 inch tire was killing my trap speeds and this one lug did not cooperate. They all went on hand tight and were torqued with a torque wrench.. ah well... beats blowing a ten bolt up :rofl:

[Blackbirdws6]

You do realize that your "hand tight" is problem good for an easy 80 ft lbs of torque right. I bet you wouldn't even feel a cross thread at this point. Poor stud...it never saw this coming.

[91chevywt]

Looks like wheel studs aren't your friend. Maybe if you buy them in bulk they'll give you a discount

[69BirdX]

Cross thread for the win

[Frosty]

Sounds like you jersey shore guys had a rough day yesterday.

[69BirdX]

Sounds like you jersey shore guys had a rough day yesterday.

To much fist pumping. But on a serious note next tine turn the lug backwards so it clicks in before tightening. It'll make sure the threads are lined up. 90 percent of the time that will keep you from coss threading. Note I said 90 because there are plenty of special people that still will

[KirkEvil]

Sounds like you jersey shore guys had a rough day yesterday.

Its a give and take...rough day but everyone got PB runs.

[noboundreez2345]

Sounds like you jersey shore guys had a rough day yesterday.

Me and Kirk had new best yesterday in one piece so it was literally 50/50. Lt1's also had new pb's but with problems. Awesome time yesterday enjoyed meeting more and seeing more of everyones rides.

[WildBillyT]

Cross thread for the win

Could be...

Matt, I take it you ran Adam's shank lugs then? Does he know if they are EXACTLY the right ones? Not all shank lugs are created equal. They can be off by fractions of an inch and chew studs.

[transmaro93]

adam got those used with the wheels so he probably has no clue who makes the lugs or any of the specs other than they are the correct thread...

[WildBillyT]

adam got those used with the wheels so he probably has no clue who makes the lugs or any of the specs other than they are the correct thread...

If he knows the model and size, Summit lists the lug specs on their site. Definetly worth a look IMO

[LTb1ow]

Granted this site thinks I am the retard, but cross threading a 2 1/2 inch nut? Cmon.

Beats me, they all went on nicely the night before.

[transmaro93]

with those shanked nuts it doesnt take much heat or fatigue to screw them up.. iv had my share of problems with them on my wheels too... but i think i got it down now so its not a problem anymore

[JL8Jeff]

I've had a few messed up/cross threaded lugs on some of the newer Camaros I've had. I had to cut one front lug off as it was cross threaded so bad someone messed up the lug key as well. It was most likely a messed up lug that went on crossthreaded and didn't put up much resistance so it torqued down like normal.

[BigAls87Z28]

This is possible. With Smash's 70004492343434342342423.4 ftlbs of torque output per arm, Im surprised he didnt snap all of them.
We figured there would be a GP on 12 bolts, with axles flying out like Scud missles. But all that happend was a busted stud and a possible blown input shaft.
The DS didnt spin when he put it "in gear".

[sweetbmxrider]

you owe me some forearm skin pal

[LTb1ow]

you owe me some forearm skin pal

You owe me some ARP studs pal.

[KirkEvil]

studs for foreskin? wtf are you pals in to?

[transmaro93]

hey matt you may have beat me cause i suck at the driving... but my car still runs faster than yours... fix your photo submission for car of the month PAL!

[sweetbmxrider]

You owe me some ARP studs pal.

you owe me a shank....or skank. your pick pal

[69BirdX]

If the threads where already slightly screwed up it wouldn't be hard to cross thread them and not notice. Cheap lugs with soft metal. I've done quite a few times. I'm sure most people have. It's unavoidable

[sweetbmxrider]

i don't really care to dive into could be's but the portion of the stud was sticking out of the shank that is stripped. i believe it was a heat issue but its over now and i still have a chunk of flesh missing. :lol:

[KirkEvil]

i don't really care to dive into could be's but the portion of the stud was sticking out of the shank that is stripped. i believe it was a heat issue but its over now and i still have a chunk of flesh missing. :lol:

Never stand on the other side of a Kohler Smash!

[LTb1ow]

http://sphotos.ak.fbcdn.net/hphotos-ak-snc6/hs074.snc6/168460_1766633561646_1113366798_2087497_6880143_n. jpg

Months later, and the old one is out. ARP hooked me up with a brand new stud free of charge, good people.

Thread is pretty mangled, looks like due to heat.

[sweetbmxrider]

Leaning Stud of Smash!

[BonzoHansen]

due to heat?

[LTb1ow]

due to heat?

Yea, some of the threads are molded together, pretty sure when taking off the shank lug the stud got hot.

[sweetbmxrider]

The lug also expanded in the center of the shank and we cooled it down with water a few times.

[Blackbirdws6]

Threads look good towards the bottom.

[JL8Jeff]

Yea, some of the threads are molded together, pretty sure when taking off the shank lug the stud got hot.

Well don't turn the lugwrench so fast! Just because you have super powers doesn't mean you need to use them all the time. :mrgreen: