Cam ?
 

ok here it goes i might be getting a Custom Grind Cam (specs 226/234 @ .050, .568/.568 on a 110LSA ) designed for an LT1, now the ? i have is would it work and run in a 305 just wondering if its possable

thanks

yeah a 305 is a conventional Small Block with the distributor in the rear of the motor compared to the LT1 style Opti up front, I DONT believe it will work. However I could be very wrong.

yes i was getting mixed anwser's i was told yes becuz an LT1 block was the same then no becuz a 305 is older so i don't know i just want a straght anwsers yoy know

It'll fit in the block. LT1 cams are roller cams, and they don't usually have the lobe on the front for a mechanical fuel pump if you have one.

That being said....that's a lot of cam for a 305. If you want to use that you better have good heads & intake on it.

- Justin

will be a 305 TPI with stock heads and stock intake for now

you sure .. i could of almost remembered having that lobe on all the ones. (never really looked "for them") but i thought they had them

aside that, justins right. I don't even think the stock heads would handle that much lift. i could be wrong

The stock LT1 cam that's sitting in my garage doesn't have one.....

- Justin

so i would need to use aftermarket heads and intake it will might work but there could be a chance the block could bascly BLOW

Wouldn't tear the block apart, but a TPI intake would be horrible for a cam like that. Good heads and a carb-style intake would be a must....

- Justin

naw im done with CARB sick of it thats why im parting out my 89 im getting an iroc TPI vert and i dont want to do head work just a cam and headers and bore out TPI thats bascily it

all you need to make an lt1 based cam fit an earlier 305/350 is to grind down the dowel pin on the end a bit. As far as lift goes, changing springs would be recomennded at that lift, Also like justin said, tpi wont like that cam too much, its made for a different power range where the tpi will choke. A converted LT1 intake alone would be an improvement.

If you wanna do a cam only setup, then I would recommend a stock LT1 cam over that one that you listed....

- Justin

would a stock LT1 cam do basicly what an aftermarket one would without charging over so much junk

Stock LT1 cam isn't nearly as aggressive as the one you posted specs for, but it will still be a noticeable increase over stock. Fresh valvesprings would still be a good idea, but it will work with your stock heads and intake much better.

- Justin

ok cool thats what i wanted to know thanks everyone looks like im looking for a good stock LT1 cam

I have 2 stock LT1 cams if your interested.

I've put a few LT4 hotcam's in GEN 1 cars, only thing you have to do is tap the dowel on the front of the cam (where the opti goes) in so it doesn't hit the timing cover. In fact the LT4 cam is optional for Chevy's ZZ4 smallblock. If you have a post 86 1 piece rear main roller block you should be fine. The LT4 cam also has the mechanical fuel pump lobe but I don't think the stockers do.
-Nick

FWIW

Technical Notes: The LT4 camshaft P/N 24502586 was designed to be used in a number of different engines. Therefore, the following change may need to be made to allow for correct assembly of the engine: For LT1 and L98 engines 1995 and before, the dowel pin in the end of the camshaft must be pushed in so extension from end of cam is .30+/-.01", the same as the production part. For 1996 LT1 and LT4 engines, the dowel pin is in the correct position, extending .620" from the end of the camshaft. This camshaft has a fuel pump lobe.

i know it is a different cam but the tech advice should be the same.

naw thanks got one coming

thanks for the info