TPI, HSR, Fuel Injection, Headers and Transmission Parts
 

This is what is left from my 327/T10 part out. I am installing an LS6 and have no need for my Small Block Parts anymore.

Polished Holley Stealth Ram with Fuel Rails, TPI Throttle Body with removed crossover passage and Lokar Throttle Cable Bracket for standard SBC heads. Part Number 701R-126. This was cast on 12/03/01. Ports appear to be 1.75" by 1.90" Sold

http://www.apiem.com/camaro/post/ForSale/HSR.JPG
http://www.apiem.com/camaro/post/ForSale/HSR2.JPG
http://www.apiem.com/camaro/post/ForSale/HSR3.JPG
http://www.apiem.com/camaro/post/ForSale/HSR4.JPG
http://www.apiem.com/camaro/post/ForSale/HSR5.JPG
http://www.apiem.com/camaro/post/ForSale/HSR6.JPG
http://www.apiem.com/camaro/post/ForSale/HSR7.JPG
http://www.apiem.com/camaro/post/ForSale/HSR8.JPG
http://www.apiem.com/camaro/post/ForSale/HSR9.JPG
http://www.apiem.com/camaro/post/ForSale/HSR10.JPG


Factory TPI MAF Computer EFI controller with Moates G1 Memory Adapter with rewritable chip. Harness was stripped of unnecessary wires. Computer is a 1227165 ECU running 6E APYPWB code with Wideband Data Logging (http://www.thirdgen.org/techboard/di...e-linear.html). Harness will come with MAF relays, EST box and Heated Narrowband O2 sensor. You will need to supply your own Wideband O2 input signal from a Wideband gauge. All cut wires are clearly marked and labled. Harness is covered in Jegs Flexbraid on most of the engine sections and a corrugated tubing over the rest. Sold

http://www.apiem.com/camaro/post/For...PI_Harness.JPG
http://www.apiem.com/camaro/post/For...I_Harness2.JPG
http://www.apiem.com/camaro/post/For...I_Harness3.JPG
http://www.apiem.com/camaro/post/For...I_Harness4.JPG
http://www.apiem.com/camaro/post/For...I_Harness5.JPG
http://www.apiem.com/camaro/post/For...I_Harness6.JPG
http://www.apiem.com/camaro/post/ForSale/computer.jpg

Factory TPI 350 22lb injectors part number 17087325 Sold

http://www.apiem.com/camaro/post/ForSale/TPI_INJ_22.JPG

Factory TPI manifold with fuel rail. Manifold is a MAF manifold with the 9th injector. The 9th injector hole has been blocked with a plug and the fuel rail was modified with -8 feed and return fittings in the rear. Has aluminum distributor cover, Thermostat housing and all correct bolts are included. $150 + shipping

http://www.apiem.com/camaro/post/ForSale/TPI.JPG
http://www.apiem.com/camaro/post/ForSale/TPI2.JPG
http://www.apiem.com/camaro/post/ForSale/TPI.3JPG
http://www.apiem.com/camaro/post/ForSale/TPI4.JPG
http://www.apiem.com/camaro/post/ForSale/TPI5.JPG


Factory MAF, Spectre intake tubing and 9 inch AEM Dryflow filter $75 + shipping

http://www.apiem.com/camaro/post/ForSale/Intake_MAF.JPG
http://www.apiem.com/camaro/post/For...ntake_MAF2.JPG
http://www.apiem.com/camaro/post/For...ntake_MAF3.JPG


36lb Injectors. Part Number 0280156811 These were cleaned and tested by South Bay Fuel Injectors on 08/16/13 and worked perfect. $150 + shipping

http://www.apiem.com/camaro/post/ForSale/Injectors.JPG
http://www.apiem.com/camaro/post/For...20(Medium).jpg

Large Cap GM TPI distributor with GM HEI Coil and Cap. Sold

http://www.apiem.com/camaro/post/For...str_LrgCap.JPG
http://www.apiem.com/camaro/post/For...tr_LrgCap2.JPG


Small Cap GM distributor with GM module, MSD Cap and Rotor, and MSD Streetfire Wires for under header routing with heat boots. $75 + shipping

http://www.apiem.com/camaro/post/For...str_SmlCap.JPG
http://www.apiem.com/camaro/post/For...tr_SmlCap2.JPG
http://www.apiem.com/camaro/post/For...tr_SmlCap3.JPG

MSD Blaster Coil 8226 for TPI/TBI engines with custom aluminum mount to mount coil to the back of the head. $30 + shipping

http://www.apiem.com/camaro/post/ForSale/Coil.JPG
http://www.apiem.com/camaro/post/ForSale/Coil2.JPG

The following parts are for a Second Generation Camaro (70-81). They may also fit a Firebird with a SBC installed.

Hedman Hedders long tube headers with O2 bungs welded in for 70-81 Camaro. 1 5/8 in primary tubes. $50 + shipping

http://www.apiem.com/camaro/post/ForSale/Headers.JPG
http://www.apiem.com/camaro/post/ForSale/Headers2.JPG


Clutch linkage and pedals package. This is the Z-bar with linkage, frame bracket, stud and rubber firewall boot. Also included is the reverse lockout for a Super T10 with the Hurst Shifter. These are all the accessories needed to install a manual transmission. SOLD.

http://www.apiem.com/camaro/post/For...tch_Pieces.JPG
http://www.apiem.com/camaro/post/For...ch_Pieces2.JPG
http://www.apiem.com/camaro/post/For...ch_Pieces3.JPG

Manual transmission parts sold.

Holley Stealth Ram, Factory TPI manifold, Factory MAF package, Small Cap GM distributor and Headers still for sale. MSD coil is pending.

HSR Sold. The following is still available.

-Factory TPI manifold with fuel rail
-Factory MAF, Spectre intake tubing and 9 inch AEM Dryflow filter
-Small Cap GM distributor with GM module, MSD Cap and Rotor, and MSD Streetfire Wires
-Headers