the project has begun

[84HOtransam]

well the project on my car has begun..working 2 jobs and 60 hours a week only helps fill the bank account..sundays are my only day off so i make use of them..

i spent 2 hours pulling the old rear from my car..the 9inch was ordered from ttp last week..

the rest of the drive train is still being decided..

either cammed and carbed ls1/t56 or built 355/tko600 trans

tubular kmember, a-arms, front coilover, manual steering, no a/c, electric water pump and sphoon torque arm.

not sure which will provide the best out come but im leaning towards the ls1..ill keep everyone updated.

[NJSPEEDER]

go with bmr on all yoru suspension stuff. since you are already spending the money you should go with chromoly. do it once, do it right, do it lite. :P
what gears are you looking at?

www.contemporarycorvette.com <<<< these guys can hook you up with a LS1 + T56 combo at a good price.

good luck

later
tim

[camaro2you]

whats happening with that rear?

[84HOtransam]

Originally Posted by NJSPEEDER

go with bmr on all yoru suspension stuff. since you are already spending the money you should go with chromoly. do it once, do it right, do it lite. :P
what gears are you looking at?

www.contemporarycorvette.com <<<< these guys can hook you up with a LS1 + T56 combo at a good price.

good luck

later
tim

i ordered it with 4.30's and a detroit tru trac 31 spline axles.. the auburn was on national back order

im trying to find a low miles (under 30k) setup..ill email them today.

i cant find a bmr kmember for third gens only one from pa racing.
where should i look for the manual steering rack

[Tru2Chevy]

You can get a manual steering box from an S-10 (you just have to swap the pitman arm). I have one in my car now, but it will prolly end up getting replaced by a WS6 box.....

- Justin

[84HOtransam]

Originally Posted by Tru2Chevy

You can get a manual steering box from an S-10 (you just have to swap the pitman arm). I have one in my car now, but it will prolly end up getting replaced by a WS6 box.....

- Justin

so take the s10 box and use my pitman arm on it...

would you be willing to sell the s10 box you have..

[Tru2Chevy]

Originally Posted by 84HOtransam

so take the s10 box and use my pitman arm on it...

would you be willing to sell the s10 box you have..

I would, but it's not mine. I'm pretty sure that it's Tim's (NJSPEEDER)....if not, then it's Bill's (foff667).

- Justin

[NJSPEEDER]

Originally Posted by 84HOtransam

i ordered it with 4.30's and a detroit tru trac 31 spline axles.. the auburn was on national back order

im trying to find a low miles (under 30k) setup..ill email them today.

i cant find a bmr kmember for third gens only one from pa racing.
where should i look for the manual steering rack

thunder racing has the manual racks for sale as well. they are actually on the same page as teh PA k-members.
here is the bmr stuff, you can order straight from them or through thunder racing http://www.bmrfabrication.com/F3-chassis.htm
bmr is really good stuff. highly recomend them over PA.

later
tim

[formulaMARK]

Originally Posted by camaro2you

whats happening with that rear?

Its in my garage.

[ar0ck]

Id like to see an LS1 in their, but thats just me

Hope everything works out for you Joe.

[78camaro]

Originally Posted by formulaMARK

Its in my garage.

[Tru2Chevy]

Originally Posted by NJSPEEDER

thunder racing has the manual racks for sale as well. they are actually on the same page as teh PA k-members.
here is the bmr stuff, you can order straight from them or through thunder racing http://www.bmrfabrication.com/F3-chassis.htm
bmr is really good stuff. highly recomend them over PA.

Thunder Racing sells the full manual rack for $625, but PA Racing sells the same kit on their website for only $565.

Can you retain the standard 3rd gen steering box with an aftermarket k-member?

- Justin

[84HOtransam]

Originally Posted by Tru2Chevy

Thunder Racing sells the full manual rack for $625, but PA Racing sells the same kit on their website for only $565.

Can you retain the standard 3rd gen steering box with an aftermarket k-member?

- Justin

not sure..im still looking into it..