|
02-12-2010, 06:55 AM
|
#1
|
Join Date: Nov 2009
Location: Williamstown, NJ
Posts: 246
|
Corvette C5 Wheels
I got lucky and got a set of C5 wheels and tires for free. Was going to put them on my 99 Firebird. Specs are Front = 17" x 8.5" Rear= 18" x 9.5". Should that be fine for clearance or will i have to start bending things back on a stock suspension? And if so, any ideas how?
__________________
IF IM NOT MAKING SOMEONE MAD, IM NOT DOING SOMETHING RIGHT
Quote:
Originally Posted by micbegz28
how much for the italian lions??? \
|
Quote:
Originally Posted by BigAls87Z28
My money is that its Chaney....
|
|
|
|
02-12-2010, 07:17 AM
|
#2
|
Join Date: Dec 2004
Location: Browns Mills NJ/ Rotondo West FL
Posts: 3,054
|
Might need a big hammer and make some room for yourself.
__________________
AI HCR 241's , Lunati 223/236 .615/.626 114+2 , Full Exhaust , Ported Fast 92 , Ported LS2 TB , Veraram , 85mm MAF , Circle D 4000 , 3.42's , GTP 36# , CSP Dyno tune. More on the way
420 HP/367 TQ on a Unlocked Converter & still climbing.
|
|
|
02-12-2010, 08:20 AM
|
#3
|
Resident Camera Guy
Join Date: Aug 2004
Location: North Jersey
Posts: 10,971
|
Quote:
Originally Posted by MonmouthCtyAntz
Might need a big hammer and make some room for yourself.
|
He'll be fine with 9.5" rears.
You'll be fine, just slap them on and drive on off into the sunset.
__________________
Last edited by ar0ck; 02-12-2010 at 08:21 AM.
|
|
|
02-12-2010, 08:34 AM
|
#4
|
Join Date: May 2008
Posts: 817
|
if they're y2k's you might have to do a little hammering. they're not very wide but the offset(63mm) causes them to sit "in" a little further than most other wheels. mine would rub a tiny bit when making hard turns, and my rear is probably closer to centered than stock.
lots of people run 1/2" spacers in the front and 1" in the rear so they don't tuck as much, but i didn't think they looked bad just bolting them up.
__________________
|2000 Trans Am|T56 swap|Bolt Ons| Suspension|
Last edited by creeper; 02-12-2010 at 08:49 AM.
|
|
|
02-12-2010, 08:42 AM
|
#5
|
12 Second Club
Join Date: Aug 2004
Location: Oradell
Posts: 8,368
|
i had wagon wheels on my 95 Z28 and the rear needed the BFH mod
__________________
86 Camaro
88 Camaro
95 Impala SS
97 Trans Am WS6
98 Blazer ZR2
00 Corvette
04 CTS-V
07 Sublime Charger Daytona
10 Tahoe SSV
12 Tahoe LT
17 Malibu LT
|
|
|
02-12-2010, 11:39 AM
|
#6
|
Join Date: Oct 2008
Posts: 814
|
They should be fine...I had 18 inch Z06 rims on my Z28, 295 tires, and they fit with no mods
__________________
Formerly known as njbadaSS
|
|
|
02-12-2010, 11:40 AM
|
#7
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
Be prepared for the rake.
|
|
|
02-12-2010, 11:52 AM
|
#8
|
Resident Camera Guy
Join Date: Aug 2004
Location: North Jersey
Posts: 10,971
|
Quote:
Originally Posted by LTs1ow
Be prepared for the rake.
|
What rake?
__________________
|
|
|
02-12-2010, 03:32 PM
|
#9
|
Join Date: Nov 2009
Location: Williamstown, NJ
Posts: 246
|
Slow-V6 has them on his car, and he had to use the BFH mod lol. They look great though.
__________________
IF IM NOT MAKING SOMEONE MAD, IM NOT DOING SOMETHING RIGHT
Quote:
Originally Posted by micbegz28
how much for the italian lions??? \
|
Quote:
Originally Posted by BigAls87Z28
My money is that its Chaney....
|
|
|
|
02-12-2010, 11:27 PM
|
#10
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
Dude when are we picking these up from Joe...I haz BFH too for the "mod"
|
|
|
02-13-2010, 05:54 AM
|
#11
|
Join Date: Apr 2008
Location: Delran
Posts: 6,785
|
best way to find out is to put em on and check. its not really a waste of money cause plenty of people have gotten vette wheels to work without a problem. the wheels on my t/a were 11'' wide too and they fit without any hammering, but again the offset is where that comes into play.
Quote:
Yesterday 12:40 PM
LTs1ow Be prepared for the rake.
|
rake!
|
|
|
02-13-2010, 02:47 PM
|
#12
|
Join Date: Aug 2005
Location: Blackwood, NJ
Posts: 2,295
|
Just a little banging was needed on my car. All I really needed was a little spacer but I thought it would be safer without the spacer. The fronts fit fine just the backs needed a little banging.
Did homeboy with the C5R finnally get new rims?
__________________
Jeff
2002 WS6 T/A.. M6..Built 383 TMR tune..461rwhp,458rwtq
2009 G8 GT. Bone stock 13.6@103.. Vararam Intake, GXP Axlebacks, LS2 FRC's
1998 Corvette Convertible, Vararam Intake+Power Duct, Fast 90/90, Ti Axleback..12.8@110
2003 Cobra Convertible 10th Anniversary
http://www.fquick.com/slow-v6
Local car cruise schedule..
http://www.cliffscalendar.com/
|
|
|
02-16-2010, 09:05 AM
|
#13
|
Join Date: Nov 2009
Location: Williamstown, NJ
Posts: 246
|
Yea, think he ordered the carbon fiber ones. He just needs tires now, then i can go pick up all his old ones, both sets lol
__________________
IF IM NOT MAKING SOMEONE MAD, IM NOT DOING SOMETHING RIGHT
Quote:
Originally Posted by micbegz28
how much for the italian lions??? \
|
Quote:
Originally Posted by BigAls87Z28
My money is that its Chaney....
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|