Today's Posts Mark Forums Read Calendar
Go Back   NJFBOA - Home of New Jersey's Camaros and Firebirds > Tech Forums > Brake, Chassis and Suspension Tech

Notices


Reply
 
Thread Tools
Old 08-18-2010, 10:19 PM   #1
1972LT1
The Plague
 
1972LT1's Avatar
 
Join Date: Dec 2005
Location: Cherry Hill
Posts: 955
iTrader: (0)
Wrangler problem

I have an 04 . In the past when the alingment was out the front wheels would start shaking and then it would cause the whole vehicle to shake. I got an alingment job done today and it hasn't gotten any better. It shakes @ 50mph. While it's shaking if I ease the wheel to the left it gets worse. If I ease it to the right it settles down. Anyone have a clue?
__________________
www.cardomain.com/id/1972lt-1
My sanity wrote a suicide note.....one of us is illiterate and the other is blind.-OTEP
That is not dead which can eternal lie, and in stranger aeons even death may die-H.P.L.
1972LT1 is offline   Reply With Quote
Old 08-18-2010, 10:22 PM   #2
BonzoHansen
Admin.
 
BonzoHansen's Avatar
 
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,153
iTrader: (27)
have the front wheels balanced at least to eliminate that. check for front end wear and maybe bearing play. one of the wack job jeep owners here might know some common issues with jeeps.
__________________
Vent Windows Forever!

The looser the waistband, the deeper the quicksand. Or so I have read.

Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.

Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
BonzoHansen is offline   Reply With Quote
Old 08-18-2010, 10:47 PM   #3
Tru2Chevy
Co-Founder / Site Admin
 
Tru2Chevy's Avatar
 
Join Date: Jul 2004
Location: Ewing, NJ
Posts: 22,473
iTrader: (8)
Social Networks:

That's what my Cherokee did when the front hub / unit bearings went bad. Pretty sure that the TJs have serviceable wheel bearings though - not sure. Have you checked front axle u joints to make sure they are all in good shape?

- Justin
__________________
1999 Camry - Beigemobile DD
2002 Suburban - Wife's DD
2004 Grand Cherokee - Not running / Project / Selling?

Tru2Chevy is offline   Reply With Quote
Old 08-19-2010, 12:07 AM   #4
BigAls87Z28
 
Join Date: Jul 2004
Location: West Long Branch
Posts: 13,598
iTrader: (3)
Sounds like a some sort of hub/wheel bearing. Have them balance the tires as well so you dont have to make that trip again.
__________________
2/20/2013: They Day the ****s Stopped
BigAls87Z28 is offline   Reply With Quote
Old 08-19-2010, 07:44 AM   #5
The Fixer
 
The Fixer's Avatar
 
Join Date: Aug 2004
Location: North Jersey
Posts: 3,047
iTrader: (5)
Sounds like Death Wobble - could be the hub bearings like Justin mentioned, or also bad bushings in the control arms, or tie rods, or trackbar, or....you get the idea. A good way to find where the loose parts are is to have and someone else turn the steering wheel back and forth while the truck is on the ground and you look for any play in the steering setup. I did that with my brother-in-law on his '04 Grand Cherokee (very similar steering setup to your TJ) and we found his trackbar was shot. He could turn the steering wheel almost 1/4 turn before the trackbar would move, and that was causing his Death Wobble.
__________________
Seeya,
Steve R. in North Jersey
'16 Go-Mango Dodge Charger R/T. It's so good to be back in a V8-powered, RWD car!

Former Toy - '88 Monte SS - had lots of mods...
The Fixer is offline   Reply With Quote
Old 08-19-2010, 08:33 AM   #6
BonzoHansen
Admin.
 
BonzoHansen's Avatar
 
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,153
iTrader: (27)
And IMO all of that should have been caught by an alignment tech. Job #1 on an alignment is check the front end; shake & inspect. Especially with that kind of complaint.
__________________
Vent Windows Forever!

The looser the waistband, the deeper the quicksand. Or so I have read.

Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.

Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
BonzoHansen is offline   Reply With Quote
Old 08-19-2010, 10:22 AM   #7
1972LT1
The Plague
 
1972LT1's Avatar
 
Join Date: Dec 2005
Location: Cherry Hill
Posts: 955
iTrader: (0)
I rotated the tires and that seems to have cut out @ 80% of it. I'll take the Jeep back and have them redo it. While I had the front wheels off I looked at all the ends and it all looked ok. I yanked on the tie rods and didn't feel any play. Same with the rotors and u joints.
Also...does anyone know how long the shocks and springs are good for on average?
__________________
www.cardomain.com/id/1972lt-1
My sanity wrote a suicide note.....one of us is illiterate and the other is blind.-OTEP
That is not dead which can eternal lie, and in stranger aeons even death may die-H.P.L.
1972LT1 is offline   Reply With Quote
Old 08-23-2010, 05:12 PM   #8
mc73nova
 
mc73nova's Avatar
 
Join Date: May 2005
Location: under a roof
Posts: 2,034
iTrader: (4)
Do you have a steering stabilizer on it?
__________________
1973 Chevy Nova - best e.t.-10.04 - currently disassembled
1989 Pontiac Trans Am GTA
2016 Dodge Durango R/T
2015 Ram 3500 Dually Cummins
mc73nova is offline   Reply With Quote
Old 08-26-2010, 05:29 AM   #9
1972LT1
The Plague
 
1972LT1's Avatar
 
Join Date: Dec 2005
Location: Cherry Hill
Posts: 955
iTrader: (0)
I don't know. It's a stock 04 wrangler. I haven't done any upgrading to it.
__________________
www.cardomain.com/id/1972lt-1
My sanity wrote a suicide note.....one of us is illiterate and the other is blind.-OTEP
That is not dead which can eternal lie, and in stranger aeons even death may die-H.P.L.
1972LT1 is offline   Reply With Quote
Reply

  NJFBOA - Home of New Jersey's Camaros and Firebirds > Tech Forums > Brake, Chassis and Suspension Tech


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Sponsor List














All times are GMT -5. The time now is 04:04 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.