![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
|
07-05-2012, 11:29 AM
|
#26
|
Join Date: Apr 2009
Location: Andover, NJ
Posts: 777
|
I got an eagle crank which I had checked. It was perfect. So there should be no problems there. As for the head gaskets, I'm surprised to hear that because of the iron heads to iron block. Most head gasket problems I've heard of and worked on involved aluminum heads. I'll see if I can find a crack in the old crank. Didn't see anything off the bat. But considering the mains were the issue I'd bet there was something else.
|
|
|
07-05-2012, 11:11 PM
|
#27
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
Quote:
Originally Posted by L695speed
I got an eagle crank which I had checked. It was perfect. So there should be no problems there. As for the head gaskets, I'm surprised to hear that because of the iron heads to iron block. Most head gasket problems I've heard of and worked on involved aluminum heads. I'll see if I can find a crack in the old crank. Didn't see anything off the bat. But considering the mains were the issue I'd bet there was something else.
|
The flaw was in the gaskets themselves
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
|
|
|
07-09-2012, 02:49 PM
|
#28
|
Join Date: Apr 2009
Location: Andover, NJ
Posts: 777
|
Ah ok, got it. Anyway update on the 88 GTA. Engine is coming back together, LT1 cam is in, lifters, lifter plate, crank, timing chain and gears, pistons/rods. I could put the heads on at this point in fact. I just want to do a bit more cleaning on the heads before I put them on. Still gotta do the front timing cover, rear main seal. But the bottom of the motor just needs an oil pump installed and we're done with that, along with an oil filter adapter and oil pan.
If all goes well, I could be putting it in and have it running this weekend...if I'm lucky. That puts me right in that one month deadline I made for myself. Not bad considering I couldn't do much for at least a week while the block and rods and etc were at the machine shop.
And Note to self...GET A BETTER PISTON RING COMPRESSOR! Parts store ones suck, they work but they make what should be an easy job a pain in the ass....
Last edited by L695speed; 07-09-2012 at 02:49 PM.
|
|
|
07-10-2012, 05:46 AM
|
#29
|
Join Date: Dec 2010
Location: Hillsborough
Posts: 956
|
You should make a separate thread for the GTA
__________________
"Quality means doing it right when no one is looking."
- Henry F*rd
|
|
|
07-10-2012, 11:52 AM
|
#30
|
Join Date: Apr 2009
Location: Andover, NJ
Posts: 777
|
Quote:
Originally Posted by 88WS-6
You should make a separate thread for the GTA
|
I will....when I get around to it, just put in in here for now for those who already asked or commented in it. I'm guessing I'll find out sooner rather than later if this blows up in my face eh Matt? lol.
|
|
|
07-10-2012, 01:08 PM
|
#31
|
Join Date: Dec 2010
Location: Hillsborough
Posts: 956
|
I'm just saying that it's such an awesome car that it deserves its own thread.
You better not blow it up. I did that once already.
__________________
"Quality means doing it right when no one is looking."
- Henry F*rd
|
|
|
07-10-2012, 05:15 PM
|
#32
|
Join Date: Apr 2009
Location: Andover, NJ
Posts: 777
|
Quote:
Originally Posted by 88WS-6
I'm just saying that it's such an awesome car that it deserves its own thread.
You better not blow it up. I did that once already.
|
You'll see a thread eventually, and when you do you'll have to excuse the tools and parts on the floor as the table filled up.
As for blowing it up, I'm really hoping I don't. But as they say "Build it, blow it up, rebuild it, repeat". LMAO! I've done everything by the book keeping it as clean as I can....tough in a garage that one's brother just throws **** around in... Lubed everything that needs to be lubed and everything. We'll see how it goes. I got a motor that should have been scrapped from the start to run with the 84 so I should be able to get a clean block with new parts in there to run without issues. If something goes wrong....well more practice for me....
|
|
|
09-30-2012, 12:08 PM
|
#33
|
Join Date: Apr 2009
Location: Andover, NJ
Posts: 777
|
The car is pretty much on the back burner. I may do some little things like removing the cracked broken moulding around the T top glass. I also have a block and other misc parts to build the stroker. Right now the block is just sitting in the car to keep it out of the way. I'm hoping that a few things go my way on the job front. There is a lead I'm hoping works out in Florida, that if it goes through I'll be down there and bringing the car with me. The other deal I'm working on is me and a friend are thinking of opening a restoration shop near where he is out in Minnesota. He despises working at the toyota dealer he is working at now, and wants to get back into the older car game. We were discussing how we could get our name out if we did it, and this car and his 71 T bird are among the options to do as a finished example of our work that we could take to shows. Either way, once I get some decent money coming in this one will be done fairly quick. Only difference is, if we open that shop, this car will have a complete paint job as well. Whereas if I go to florida it may be some time still before its painted.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|