 |
08-31-2013, 08:00 PM
|
#1
|
Join Date: Oct 2010
Posts: 70
|
SBC carbed 350 in 85 monte popping through exhaust on pass side?????????
Ok heres the deal I picked up an 85ss monte with a 78 Camaro 350 in it.
car sat for 4 years headers rusted off of it car started up and ran good only ran it for a few minutes to load on the trailer and bring it home I have no history on car other then it sat for 4 years.
I just installed brand new long tube headers on it along with a new starter and new accel plugs because that's what I had on my shelf at the time figured why not use them anyway now that I have the exhaust hooked up and started the car up it is popping out of the pass side exhaust its at idle and through the rpm sweep. only ran the motor for about 2 minutes and shut it down. Has a weind intake and edlejunk carb on it. Car has true duals with no h pipe or x pipe so I know for certain it is out of the pass side. I just changed the valve cover gaskets as well and its stock heads with stock stamped steel rockers some of them felt a little loose. Trying to figure out what could be the cause of the popping problem I have not replaced the cap rotor or plugs yet but they did seem to in ok shape. Any ideas on what to look for would be appreciated. thanks guys
|
|
|
|
08-31-2013, 10:00 PM
|
#2
|
Join Date: Nov 2012
Location: Millstone, NJ
Posts: 641
|
Ive always thought popping means wiped out exhaust cam lobe
__________________
94 TA GT. Stock 350, cam, exhaust
|
|
|
|
|
09-01-2013, 12:25 AM
|
#3
|
Join Date: Feb 2010
Location: Stillwater
Posts: 822
|
Uh I read about three lines of your post. Are they the right reach plugs for the heads? You can easily get a nasty miss from the wrong plugs, risk having a piston hitting a plug, etc.
__________________
Quote:
Originally Posted by LTb1ow
...its cool to like diesels, cause that and pretending to be country is like, hip nowadays!!
|
|
|
|
|
|
09-01-2013, 10:23 AM
|
#4
|
Join Date: Oct 2010
Posts: 70
|
Same brand plugs that I pulled out of it but not sure how it ran with the prior plugs due to motor was loud being that the headers were rusted off of it.
|
|
|
|
|
09-01-2013, 05:02 PM
|
#5
|
|
Co-Founder / Site Admin
Join Date: Jul 2004
Location: Ewing, NJ
Posts: 22,473
|
You should verify what plugs are needed and make sure you replace with the same ones. Same brand doesn't mean squat - there are different lengths, different heat ranges, etc and that will all affect how the engine runs.
- Justin
__________________
1999 Camry - Beigemobile DD
2002 Suburban - Wife's DD
2004 Grand Cherokee - Not running / Project / Selling?
|
|
|
|
|
09-01-2013, 06:16 PM
|
#6
|
Join Date: Feb 2005
Location: west orange nj
Posts: 2,415
|
Tune the motor I had the same prob it turned out to be a bad dist cap
|
|
|
|
|
09-01-2013, 06:47 PM
|
#7
|
Join Date: Aug 2013
Location: Woodbridge twsp.
Posts: 16
|
At some point in the near future I would think about doing a compression/leak down test to get an idea of cond. of engine internals. I prefer the leak down test, If there is a bad valve or piston ring this will be better to pinpoint the problem. You said you have no history on engine. I would do this and the basics in the other posts before throwing a lot of money at trying to fix it.
|
|
|
|
|
09-01-2013, 07:34 PM
|
#8
|
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,650
|
Compression test will show wiped cam lobe, leakdown will not.
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41
Quote:
Originally Posted by Blackbirdws6
I can appreciate a dream but this person needed some real friends.
|
|
|
|
|
|
09-01-2013, 08:44 PM
|
#9
|
Join Date: Oct 2010
Posts: 70
|
By saying same brand ment same brand and part number sorry for not specifying that.....
I also today spent some time messing with it at first I pulled the valve cover and cranked it over without the hot wiring going to the distributor. Looked for any valves that were not moving as much as the rest everything seemed fine.
I then pulled the wire for the back cylinder and started it up and had no popping out of the exhaust.
At that point I retraced all of the plug wires being that I was in a rush the first time to get it started up. Found that cyl 5 and 7 wires were crossed switched them around started it up and runs good now. Glad it was something as stupid as that the first day i just got fusterated working on it once i got it started and it was popping i just shut the hood and walked away.
|
|
|
|
|
09-01-2013, 09:16 PM
|
#10
|
|
11 second club / Moderator
Join Date: Aug 2004
Location: West Berlin, NJ
Posts: 7,148
|
Glad is was something easily fixed
__________________
2001 Trans Am WS6 •SLP Loudmouth II •UMI Suspension •12.857 @ 109.57
1996 Trans Am WS6 •Pacesetter Longtubes •Strange 12 Bolt •Spohn Suspension •11.152 @ 123.85
|
|
|
|
|
09-01-2013, 09:36 PM
|
#11
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by 89firebird
By saying same brand ment same brand and part number sorry for not specifying that.....
I also today spent some time messing with it at first I pulled the valve cover and cranked it over without the hot wiring going to the distributor. Looked for any valves that were not moving as much as the rest everything seemed fine.
I then pulled the wire for the back cylinder and started it up and had no popping out of the exhaust.
At that point I retraced all of the plug wires being that I was in a rush the first time to get it started up. Found that cyl 5 and 7 wires were crossed switched them around started it up and runs good now. Glad it was something as stupid as that the first day i just got fusterated working on it once i got it started and it was popping i just shut the hood and walked away.
|
DAMN!
Too slow. I read the first post and my initial thought was firing order. Glad you figured it out.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
