Today's Posts Mark Forums Read Calendar
Go Back   NJFBOA - Home of New Jersey's Camaros and Firebirds > Camaros, Firebirds and the People that own them > Member's Projects

Notices


Reply
 
Thread Tools
Old 11-20-2014, 07:21 PM   #1
IROCZman15
10 Second Club / Meet Coordinator
 
IROCZman15's Avatar
 
Join Date: Dec 2004
Location: Roxbury, NJ
Posts: 2,118
iTrader: (8)
New exhaust on daily driver truck .. at CTW motorsports

Most recent automotive project/upgrade was this... nothing too major, but it was completely necessary

Paul (of CTW MOTORSPORTS)got me a great price on a magnaflow exhaust for my Daily-driver dodge ram pickup and when it arrived I went down to his hop in Hillsborough and we installed it in a few hours time. he also sold me more awesome auto detailing products and had a ton of tools at the ready (let alone a nice warm place to do the install.. instead of on my back, in the driveway, in 30 degree windy weather). Much thanks to Paul for the great price and shop use.





Copy and paste from my post on www.ramforum.com:


This is just a post to document my install of Magnaflow exhaust kit #16700 on my 2006 Dodge Ram 1500 Quad Cab 5.7 . I ran a bunch of searches on this site prior to even purchasing this kit, just to see what I was up against during the install and didn't find really that much info. I did check out all the exhaust videos/audio files on one thread on this site.. and I plan on making one of those once I have a proper camera and a person to film as I drive through the gears.

So, basically I added a full stainless steel cat-back Magnaflow exhaust setup to the Dodge Ram. Prior to this, the truck sounded so quiet and wimpy. It had the factory exhaust on it which includes three mufflers.. (well two mufflers and a tailpipe un-resonator). It was ridiculously QUIET, especially for a truck with a 5.7 hemi in it. Basically when I turned it on I just heard the pulleys and belt spinning... and while driving, I just heard air/wind... you could not hear any sound or tone from the engine or exhaust...even at WOT it was tough to hear anything.

I decided to get this system from my buddy Paul at CTW motorsports in Hillsborough NJ, and he was able to save me $130 off of what the normal online retailers charge! I paid $621.51 and it retails through most major suppliers for $749.83. I also decided to go for the dual tailpipe setup for cosmetic reasons because it looks way better than a single pipe lazily hanging out behind the rear passenger tire.



This is Magnaflow kit #16700. It included a 3" main pipe, SI-DO "single in - dual out" muffler, mandrel bent 2.5" tailpipes and 3" stainless tips. all pipes are stainless steel too. All band-clamps were included too.

I ended up taking a few hours out and installing this at Paul's shop since my other option was to install it outside in the 35 degree windy weather, on my back, in the driveway. Paul was a big help and let me use all his air-tools and facility. Thanks dude.

We spent about an hour removing the stock exhaust, which was 30 mins more than I had planned on. I was unaware that there would be several spot welds holding some of the pipes together where they joined up... so that slowed us down from simply unbolting and removing the components....to actually cutting the stock system apart.

The install went together very easily. We made sure all components were accounted for and assembled it rough on the shop floor. Then, starting with the main pipe we slid it all into place, working front to rear. The biggest issue we had was the mounting stud that Magnaflow makes you install into the frame to make this system a dual exit setup. We could not think of an easy way to get the provided nut to stay in place while we tightened the threaded mounting post (photos below). yet 1/4 turn at a time we got it threaded up. Otherwise all of the install was quite simple.

Photos are attached of the overall install, the different pieces of the system, and the finished setup. These are mostly for anyone considering this system, so they have a good idea of what is supplied and what is involved.

The video recording does it no justice. In real life, it sounds deep and throaty, but still mellow enough not to irritate my neighbors or create drone in the driver compartment. I only revved it up to 3500 ish rpms in the video link below, but it sounds best when the engine is under load and accelerating through the gears. I'll try to get a few videos of that one days soon. I'll try,but unfortunately it's been very cold here in NJ and haven't had time to grab anybody to go for a ride-along videotape yet.





























side view of tips




the 3 vehicles I get to choose to drive. All with their own positives and negatives:






crappy video:
please... ONLY listen to it on an actual computer with real speakers. cell phones and small devices are unable to play low tones.

http://vid15.photobucket.com/albums/...5/DSCN2905.mp4
__________________
1987 IROC-Z - modified

IROCZman15 is offline   Reply With Quote
Old 11-20-2014, 07:26 PM   #2
WildBillyT
Ayatollah of Rock N Rolla / Admin
 
WildBillyT's Avatar
 
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
iTrader: (10)
What a nice, clean install!
WildBillyT is offline   Reply With Quote
Old 11-20-2014, 11:22 PM   #3
greenformula92
 
greenformula92's Avatar
 
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
iTrader: (1)
Sounds good. Could be a little louder but that just goes to my tastes
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO

2018 Silverado 1500
greenformula92 is offline   Reply With Quote
Old 11-21-2014, 07:15 AM   #4
Blackbirdws6
Lord of the rings / 10 Second Club / Meet Coordinator
 
Blackbirdws6's Avatar
 
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,361
iTrader: (3)
Nice clean install. Well done.
__________________

97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140

'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
Blackbirdws6 is offline   Reply With Quote
Old 11-21-2014, 08:02 AM   #5
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,342
iTrader: (12)
Nice dude
__________________
sweetbmxrider is offline   Reply With Quote
Old 11-21-2014, 08:58 AM   #6
Artful Dodger
 
Artful Dodger's Avatar
 
Join Date: Dec 2010
Location: Moorestown
Posts: 407
iTrader: (0)
Nicely done!
__________________
Artful Dodger
Current:
2010 Camaro 2SS/RS M6 BLK, 2015 Maserati Ghibli Q4 Sport BLK (dd), 2020 Land Rover Discovery Sport BLK, 2012 MB C300 WHT
http://www.southjerseycamaro.com
Artful Dodger is offline   Reply With Quote
Old 11-21-2014, 10:44 AM   #7
Paul Huryk
 
Join Date: May 2012
Location: Bridgewater, NJ
Posts: 835
iTrader: (0)
Dave,

Glad you are happy with the system!

In all honesty, revving it stopped does it no justice - you need to hear it as it is taking off; sounds like a Hemi should. It also dropped off about 30lbs and may have picked up 15hp too.

These systems are typically an easy install - most are bolt-ons and include all clamps, hangars (usually welded in place), 409 SS mufflers (usually) and in this case, a few outlet options for aesthetics. I don't have a lift, but it was easily installed on the truck with just a pair of ramps - also did a system on the GTA using the same ramps.
__________________
1984 Camaro: 350 Auto, Global West Suspension, Baer Brakes, CTW Wheels
1989 GTA: Bolt-on L98. Global West Suspension, full Magnaflow exhaust, Wilwood Brakes, CTW Wheels
Paul Huryk is offline   Reply With Quote
Old 11-21-2014, 02:27 PM   #8
1320B4U
 
1320B4U's Avatar
 
Join Date: Oct 2009
Location: West Milford
Posts: 1,026
iTrader: (0)
Nice work! As a daily, you don't want it too loud....just enough to enjoy but not bothersome.
__________________
<img src=http://i678.photobucket.com/albums/vv143/B1320B4U/both-1.jpg border=0 alt= />

1991 Camaro
1992 L98/ttop Firehawk tribute (sold)
2006 Srt-10 Viper
2012 z-71
2011 Equinox (family vehicle)
1320B4U is offline   Reply With Quote
Reply

  NJFBOA - Home of New Jersey's Camaros and Firebirds > Camaros, Firebirds and the People that own them > Member's Projects


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Sponsor List














All times are GMT -5. The time now is 12:16 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.