![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
11-12-2018, 06:20 AM
|
#1
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Chassis coating Por15 questions
So I'm going to be taking my 01 apart soon for a motor swap and while I had the trans out I wanted to coat the floor pans with something to prevent rust. They're starting to get some surface rust around the edges and I want to keep on top of it as I plan on keeping the car. I know por15 is the most talked about but I hear that it doesn't stick to non-rusty surfaces well. I know por15 is not UV resistant and will need a top coat. Anyone have any experience with it, or another product recommendation, or something better for not rusted panels?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-12-2018, 06:39 AM
|
#2
|
Join Date: Nov 2007
Location: Jackson, NJ
Posts: 1,723
|
No matter how well I've prepped a surface, I've never had good luck with POR15.
I swapped motors in my truck recently and painted the frame with rustoleum. We'll see how it holds up but I heard it does well.
__________________
1983 camaro- Scrap
1988 camaro- Also scrap
'05 Silverado- You guessed it, scrap
1988 TRX 250R- Ported w/ high compression on 110 octane- Out 60' your LT1
Jersey Shore Street Car Takeover (JSSCT) Founder
Quote:
Originally Posted by LS1ow
and once i get PHB, what do i ajust it too?
|
Quote:
Originally Posted by Jersey Mike
Seven.
|
|
|
|
11-12-2018, 06:53 AM
|
#3
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,150
|
UV doesn't matter underst the car. It does not like smooth or painted met as l
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
11-12-2018, 07:32 AM
|
#4
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Ok so por15 only on the surfaces with rust popping thru...any suggestions on what to paint the rest with?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-12-2018, 08:12 AM
|
#5
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Anyone have any experience with Eastwood products?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-12-2018, 03:51 PM
|
#6
|
Power Member/NJFBOA Bookie/Moderator
Join Date: Jun 2009
Location: North Jersey = Best Jersey.
Posts: 4,435
|
Only thing POR15 stuck to was my skin.
__________________
1995 Firebird... Stock-ish.
Quote:
Originally Posted by LS1ow
Good. He microwaved my phone 6 years ago, i hope his intake erupts.
|
|
|
|
11-12-2018, 04:39 PM
|
#7
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by B4C
Ok so por15 only on the surfaces with rust popping thru...any suggestions on what to paint the rest with?
|
Willing to spray, with even an HF purple gun? Honestly I'd consider an epoxy primer with zinc in it. I think SPI's stuff has that and it's UV stable. You might even be able to brush it.
POR 15 has worked well for me but only on really rough surfaces. It REALLY needs tooth to work well. Was/is great on a fresh sandblasted surface but it's also come off in big flakes on floor pans.
|
|
|
11-12-2018, 08:36 PM
|
#8
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Not really willing to spray, dont have a compressor and dont want to make a mess in my dad's shop. Anyone have any experience with rust bullet? From what I've read it seems most likely to adhere to both painted and rusty surfaces and is also silver so the finish might be close to the underside if my car.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-12-2018, 09:53 PM
|
#9
|
Join Date: Jun 2016
Location: Millstone
Posts: 142
|
Spi epoxy paint
|
|
|
11-13-2018, 05:26 AM
|
#10
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by DirtyBird
Spi epoxy paint
|
That's going to stop the current rust from continuing ?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-13-2018, 09:39 AM
|
#11
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by B4C
That's going to stop the current rust from continuing ?
|
Get a rust reforming spray like metal ready, apply that following the instructions properly (emphasis on neutralizing, if you don't do it you can have adhesion problems) and coat it with a durable paint of your choosing. Metal ready (or metal prep now), Ospho, or one of those is basically an acid (like phosphoric) that leaves a zinc coating. Be aware that it works via chemical reaction so if you do it in the cold winter it may work like ****.
Seems like possible overkill but it's how you'll get a solid coating.
Last edited by WildBillyT; 11-13-2018 at 09:40 AM.
|
|
|
11-16-2018, 01:12 PM
|
#12
|
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,676
|
https://www.kbs-coatings.com/ cheaper than POR15 works just as well. hit all surfaces with 80 grit and apply as recommended.
__________________
John
|
|
|
11-16-2018, 10:01 PM
|
#13
|
10 Second Club / Meet Coordinator
Join Date: Dec 2004
Location: Roxbury, NJ
Posts: 2,111
|
I sanded almost the whole side of my Underbody down to bare metal with wire wheels,scrapers, sandpaper, etc back in 2010. It took me a few dozen hours but I did it
I drove to a POR-15 headquarters which was in Whippany NJ and spent a while talking to them and seeing products. While their product is primarily made to be painted over rust, if you use their marine clean and then the special metal ready spray and procedures and apply the por15 to a bare surface.... IT WILL WORK . the guy at their sho was showing me tons of samples. he showed me POR painted directly onto bare clean metal. even painted onto pieces of round pipe. then he banged those pipes together and the paint didn't chip or marr or break off at all.
My underside is in pristine condition anywhere I put the POr15. I have not have had one since scratch, flake, peeling, or anything like it. It is still black but has a slight brownish hue to it Very slight.
Go on my website and I have photos and description
https://iroczman15.m.webs.com/site/m...etwork=fw#3030
Also some recent photos of my underside as of March 2018 are on one of my threads on here where I had the while trans, driveshaft, exhaust, rear axle, fuel tank, exhaust out of the car.
I can’t explain why the other people had issues with their POR15 application but I can assure you that I did not. My car gets used and often it gets used hard. But I take time to get under there often and give things a wipe down pretty often. If it had flaked or peeled or acted weird anywhere I would notice it and admit it on here. It’s 100% intact and awesome after 8 years
__________________
1987 IROC-Z - modified
Last edited by IROCZman15; 11-17-2018 at 05:51 PM.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|