 |
|
03-26-2013, 03:05 PM
|
#26
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Yeah, I hear you on that one.
Regarding the cam, yeah you could swap it because there's only 2 gaskets left, but if you replace it with a flat tappet you run the risk of wiping it on break in.
If you do swap cams I have extra camshaft break in oil, with Comp's additive package. Fill motor, break in, dump oil.
|
|
|
|
03-26-2013, 03:41 PM
|
#27
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by BonzoHansen
Is that high tark?
|
F'in A!
Quote:
Originally Posted by WildBillyT
Yeah, I hear you on that one.
Regarding the cam, yeah you could swap it because there's only 2 gaskets left, but if you replace it with a flat tappet you run the risk of wiping it on break in.
If you do swap cams I have extra camshaft break in oil, with Comp's additive package. Fill motor, break in, dump oil.
|
Wiping it because of the crappy cores I have been reading about? Or you mean re-using the lifters? If you mean re-using lifters I would buy new ones, and everything else..... would probably throw the carb on for break in too if I did that, with the mechanical fuel pump and a 5 gallon can on the ground 
|
|
|
|
|
03-26-2013, 03:57 PM
|
#28
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by PolarBear
F'in A!
Wiping it because of the crappy cores I have been reading about? Or you mean re-using the lifters? If you mean re-using lifters I would buy new ones, and everything else..... would probably throw the carb on for break in too if I did that, with the mechanical fuel pump and a 5 gallon can on the ground |
Wiping because of the crappy cores. I am a firsthand victim.
With the way you make it rain I can't imagine you'd re-use lifters.
Also, you can't do that with a flat tappet cam. They seat to the lobes.
|
|
|
|
|
03-26-2013, 04:01 PM
|
#29
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by WildBillyT
Wiping because of the crappy cores. I am a firsthand victim.
With the way you make it rain I can't imagine you'd re-use lifters.
Also, you can't do that with a flat tappet cam. They seat to the lobes.
|
Yeah, I would be loathe to spend money on a flat tappet to just have it get wiped out. This has scared me off for a while, reading about experienced builders wiping cams
I would go roller too, but that's around a grand for the retrofit kit
Last edited by PolarBear; 03-26-2013 at 04:16 PM.
|
|
|
|
|
03-26-2013, 04:28 PM
|
#30
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by PolarBear
Yeah, I would be loathe to spend money on a flat tappet to just have it get wiped out. This has scared me off for a while, reading about experienced builders wiping cams
I would go roller too, but that's around a grand for the retrofit kit
|
That's why I'm questioning even going for it. The 292H I had go did it on an engine dyno at a very reputable builder's place. He took me in the dyno cell and showed what had happened and how the pushrod was not spinning. FWIW the guy that built the engine was a member of Pat Musi's crew.
Does it have an aftermarket cam in it now? Gun to my head I wouldn't jack with it if you plan on replacing it in its entirety soon. It's almost cruising season.
|
|
|
|
|
03-26-2013, 06:06 PM
|
#31
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by WildBillyT
Does it have an aftermarket cam in it now? Gun to my head I wouldn't jack with it if you plan on replacing it in its entirety soon. It's almost cruising season.
|
I dont know what is in it. It definitely has a rebuild on it now that I have checked the cylinders. No ridge at the top, still has crosshatch and the cylinders look about ~.010 over. If it is not a stock cam, its a really small upgrade. Idles smooth, great vacuum..... 
I was only contemplating since I am sooo close to what I would need to do for the change. If I kept the engine, if my cousin doesn't buy it, the 454 would go into the truck I think I decided so the cam would be beneficial to the truck too in the long run. But if I do that I can do it later too....
I'll just stick with what it has for now and hopefully the intake gasket will seal better this time.
|
|
|
|
|
03-26-2013, 06:33 PM
|
#32
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,153
|
you ever do a leak down or compression test on it?
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
|
03-26-2013, 06:57 PM
|
#33
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by BonzoHansen
you ever do a leak down or compression test on it?
|
Compression yes, leakdown no.
|
|
|
|
|
03-26-2013, 07:16 PM
|
#34
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
What did it look like?
|
|
|
|
|
03-26-2013, 07:19 PM
|
#35
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
1: ~155-160
2: 160
3: ~155-160
4: 160
5: 155
6: 155
7: 155
8: ~160
|
|
|
|
|
03-26-2013, 07:22 PM
|
#36
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Install the intake and go. Buy good gaskets that properly fit the intake ports.
|
|
|
|
|
03-26-2013, 07:25 PM
|
#37
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
New and previous gaskets are Fel-Pro. They are for the rectangle ports of the LS6 manifold. BTK and I installed this manifold and gaskets so I am pretty confident that it was done properly. I dont have a real good straight edge to check for "flatness", I have a few metal rules, but they are a bit too flexible to make an accurate judgement guess whether the flange area is not warped or anything.
|
|
|
|
|
03-26-2013, 07:30 PM
|
#38
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by PolarBear
New and previous gaskets are Fel-Pro. They are for the rectangle ports of the LS6 manifold. BTK and I installed this manifold and gaskets so I am pretty confident that it was done properly. I dont have a real good straight edge to check for "flatness", I have a few metal rules, but they are a bit too flexible to make an accurate judgement guess whether the flange area is not warped or anything.
|
Which heads?
Keep in mind I'm not questioning your or BTK's ability.
|
|
|
|
|
03-26-2013, 07:33 PM
|
#39
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by WildBillyT
Which heads?
|
Both the "new" and old heads are oval ports. LS6 manifold was the only way to get a low rise manifold with the square bore carb. So the ports are MASSIVELY mis-matched  have to use the rectangle port gasket
|
|
|
|
|
03-26-2013, 08:04 PM
|
#40
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Torker II-O?
Granted it's old tech and single plane, but at least the ports match.
|
|
|
|
|
03-26-2013, 10:37 PM
|
#41
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Oh, Scott. That silver on the car must be the original paint. Its paint code 64
|
|
|
|
|
03-26-2013, 10:39 PM
|
#42
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by WildBillyT
Torker II-O?
Granted it's old tech and single plane, but at least the ports match.
|
I think that sits taller then the LS6 manifold. Had I really decided to keep the 454 I contemplated having the ports epoxied, so it could be matched to the large ovals
|
|
|
|
|
03-28-2013, 02:44 PM
|
#43
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Are officially on order  It's only money right? I figured f-it, im going to do it. and yes, I realize I am being vague.... see who can figgir it out
Last edited by PolarBear; 03-28-2013 at 02:47 PM.
|
|
|
|
|
03-28-2013, 02:50 PM
|
#44
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
^the flanges look a lot like ls1 flanges.....
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
|
03-28-2013, 02:51 PM
|
#45
|
|
BadMod
Join Date: Aug 2004
Location: hamilton, nj
Posts: 8,889
|
I know.
__________________
So much stupid, so little time.
Quote:
Originally Posted by 79CamaroDiva
It started before I drove your car. I just have to look at it the wrong way and your car poops parts.
|
Mercerville MotorSports, LLC
|
|
|
|
|
03-28-2013, 02:56 PM
|
#46
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Those aren't BBC flanges?
|
|
|
|
|
03-28-2013, 03:13 PM
|
#47
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,342
|
Quote:
Originally Posted by PolarBear
Those aren't BBC flanges?
|
They are with a drill!
|
|
|
|
|
03-28-2013, 11:30 PM
|
#48
|
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,677
|
I can see it now. Bear trying to install ls heads on the 454.
__________________
John
|
|
|
|
|
03-29-2013, 11:57 AM
|
#49
|
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by Featherburner
I can see it now. Bear trying to install ls heads on the 454.
|
You mean my low rise LS6 manifold wont work with the aluminum LS6 block I have in the garage?
|
|
|
|
|
03-29-2013, 12:46 PM
|
#50
|
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,677
|
Quote:
Originally Posted by PolarBear
You mean my low rise LS6 manifold wont work with the aluminum LS6 block I have in the garage?
|
LS6 is LS6. With a drill and lots of self tapping screws and RTV anything is possible. 
__________________
John
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
