92 bird - Page 2 - NJFBOA - Home of New Jersey's Camaros and Firebirds

Punkmaster 98 · 03-07-2015, 04:08 PM

Ive swapped to a smaller belt now. Did some extended driving and when i return home i checked my meter. 13.38v idling. On the dash it was 1 mark below 13. I know these are not the best guages. I was thinking of installing a digital Meter Flush mounted with the rest of my after market pillar gauges going in to just keep an eye on it.

Punkmaster 98 · 03-22-2015, 12:27 PM

Got my 3200 FTI stall today. Was Recommended to me by a fellow member on here as well as Tick Performace. Looking forward to to putting it in. I took My car to a Local reputable trans shop and let them drive my car. To me the one-two shift was very hard and i initially thought something was wrong when i was just driving my swap for the first time. The shop thinks the trans was modified. The second owner of the donor vehicle has no clue. I may just leave the trans alone for the time being. I will be looking into a bigger trans cooler with a built in fan though.

Punkmaster 98 · 03-22-2015, 12:27 PM

Took my car to advanced to test the electrical system. These were the printed results. Not sure if i should maybe test with a second alt? Battery is brand new as well.

Punkmaster 98 · 03-25-2015, 03:45 PM

Had new springs and steering installed. had to cut the springs cause i forgot the new motor is lighter -_- . 2nd times the charm lol. I had a hard time finding a shop to do the alignment. they denied me after looking at the car. Its good to go now though. One part is a tiny bit out of spec though.

Punkmaster 98 · 04-12-2015, 08:28 PM

Ran into an issue last week. shattered my oil pan -_- . Thankfully I was able to save the motor. What a pita to change that out.

Punkmaster 98 · 04-12-2015, 08:32 PM

Got my ls1 brake conversion hubs from flynbye. Looked forward to installing these and making some adjustments to pressure going to my swapped rear.

V · 04-12-2015, 08:33 PM

Wow, That sucks.

What caused it to shatter? I'm doing an LS swap into my 88 Trans am and that was one of my concerns. I read the tubular k members don't provide much protection, and that there isn't much clearance with a stock k unless you cut out some of it.

Punkmaster 98 · 04-12-2015, 08:36 PM

Quote:

Originally Posted by V

Wow, That sucks.

What caused it to shatter? I'm doing an LS swap into my 88 Trans am and that was one of my concerns. I read the tubular k members don't provide much protection, and that there isn't much clearance with a stock k unless you cut out some of it.

I hit something in the road and it wedged between the road and the pan. The pickup tube bent upwards. Im using the stock kmember. i only have millimeters of clearance. I f you get the chance. notch about 1-2 in out of the kmember at the back for more clearance. will be doing that this summer. I bought another thirdgen to daily in the mean time when i start work on this one again.

V · 04-12-2015, 08:45 PM

Ah ok.
I will be running a holley pan, not the stock f body one. It will clear the stock k member much better and have basically the same ground clearance as the f body one. Its about $325 but I'm selling my '02 oil pan to cover as much of that as possible.

Here's a comparison pic of the pans...

Punkmaster 98 · 04-12-2015, 08:50 PM

i wish i knew that before llol. spent 300 on this gm performance pan.

Punkmaster 98 · 04-29-2015, 10:59 PM

Ordered some factory paint to try and color match my broken gfx with a satisfactory replacement. 3 base coats and 2 clear. It came out pretty good but im not sure if i should wetsand it?

WildBillyT · 04-30-2015, 10:43 AM

Quote:

Originally Posted by Punkmaster 98

Ordered some factory paint to try and color match my broken gfx with a satisfactory replacement. 3 base coats and 2 clear. It came out pretty good but im not sure if i should wetsand it?

Did you cut/buff it already?

Paul Huryk · 04-30-2015, 04:49 PM

It looks to have orange peel, so wet sand it first, then compound and polish...

sweetbmxrider · 04-30-2015, 07:44 PM

I was thinking the same but I only watch body guys work, no true experience here. You could have probably laid the clear a little heavier or "wetter" as this looks "dry" to my inexperienced eyes.

Punkmaster 98 · 04-30-2015, 10:24 PM

should i respray the clear or is it too late?

Punkmaster 98 · 05-03-2015, 05:34 PM

developed a ticking sound over the last two weeks that i thought was the motor. Thanksfully it was just the flexplate. I swapped it out for a thicker street/strip one.

Punkmaster 98 · 05-06-2015, 09:54 PM

New flexplate is in. Been having a start issue. installed an aftermarket starter and it wont engage. just clicks. if i rotate the crank a little it will start. I shimmed the started with the one provided and its still the same issue. more shimming?

Punkmaster 98 · 05-20-2015, 11:50 PM

I ended up returning the starter under warranty because of the start issue. SUMMIT sent me a new one. im not gonna use it as i took the oem one to a starter shop and had them replace the housing that broke so all is well now.

I bought a donor 8.8 from a 98 ford mustang GT and took it to ND fabrication in jackson to be built. they will adapt it to my thirdgen axle tubes. Going to run 4thgen 98-02 brakes and stepping up to 3.55 gears.

Punkmaster 98 · 05-31-2015, 05:36 PM

Spent some time to try and reorganize under the hood. i will be removing the factory coolant overflow jugs along with the washer fluid and relocating them elsewhere. I also welded in some t clamps to permanently route my trans cooler lines.

Punkmaster 98 · 06-06-2015, 09:49 PM

Scored this new OEM spoiler from a friend. looking forward to getting it painted and installed.

Punkmaster 98 · 07-04-2015, 02:57 PM

8.8 is complete!! just need to paint it and install my ls brakes. Big thanks to ND fabrication for the job. Def worth looking into.

Punkmaster 98 · 09-15-2016, 09:42 PM

210k my a arms and ball joints are pretty worn. I replaced the a arms with another stock factory set with new ball joints and bushings. While i was at it converted to 4thgen ls1 brakes. So far everything has went together fine minus a few small modifications.

PolarBear · 09-17-2016, 09:08 PM

You will not be disappointed in the LS1 brakes, I have them on my 92 also

Punkmaster 98 · 10-10-2016, 06:25 PM

Did a 4thgen brake conversion on the car and was having issues with the brakes and a soft pedal. Had someone assist me in bleeding and heard a loud POP and saw the mainline going to the rear had ruptured. I honestly consider this a blessing in disguise. I have a brand new stainless line that I had intended to use on my 87 but I will use it here. I will be taking the plates off this car tomorrow. When i get back from work I am pulling the motor and trans and stripping the car bare to prep it for paint.

WildBillyT · 10-11-2016, 11:19 AM

Quote:

Originally Posted by Punkmaster 98

Did a 4thgen brake conversion on the car and was having issues with the brakes and a soft pedal. Had someone assist me in bleeding and heard a loud POP and saw the mainline going to the rear had ruptured. I honestly consider this a blessing in disguise. I have a brand new stainless line that I had intended to use on my 87 but I will use it here. I will be taking the plates off this car tomorrow. When i get back from work I am pulling the motor and trans and stripping the car bare to prep it for paint.

Pic link is broken.

I'm glad the line popped now though! Ouch.