![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
|
08-14-2015, 11:30 PM
|
#76
|
Join Date: Apr 2015
Location: Sicklerville,NJ
Posts: 142
|
Ok I just put the clutch. This was my first clutch job. My brother helped me put it in . We got it up and almost in but it wouldnt go all the way in by 1/4 of an inch. I suggested we slide the trans out and rotate the shaft but he wanted to try the bolt pull in method which worked. I just dont feel great about it. I remember when I put up the disc and PP on the flywheel I just lined up the holes not any dowel pins. I am a rookie. Am I doomed?? I tried the clutch after the install as its still in the air and all seemed ok. What should I do??
|
|
|
08-15-2015, 05:24 AM
|
#77
|
Lord of the rings / 10 Second Club / Meet Coordinator
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,357
|
Last little bit was likely the input shaft going into the pilot bearing (or bushing). Pulling it in with the bolts isn't the best idea but it's probably fine.
__________________
97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140
'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
|
|
|
08-15-2015, 11:17 AM
|
#78
|
Join Date: Dec 2008
Location: NNJ
Posts: 1,489
|
Quote:
Originally Posted by cycomiko
Ok I just put the clutch. This was my first clutch job. My brother helped me put it in . We got it up and almost in but it wouldnt go all the way in by 1/4 of an inch. I suggested we slide the trans out and rotate the shaft but he wanted to try the bolt pull in method which worked. I just dont feel great about it. I remember when I put up the disc and PP on the flywheel I just lined up the holes not any dowel pins. I am a rookie. Am I doomed?? I tried the clutch after the install as its still in the air and all seemed ok. What should I do??
|
I slid the driveshaft in and rotated it to line the splines up. You wouldn't have been able to get the trans that far if they weren't lined up. There are no dowel pins on the flywheel for the PP. Did you put a new bushing / bearing in with a hammer? Could have made it out-of-round causing some friction between it and the input shaft, but it'll be fine.
__________________
1997 Camaro Z28 - 355 LT1, T56, CC503, LTs, ORY, Bald Eagle-back exhaust, !emissions, Lingenfelter CAI, EWP, !CAGS, BMR LCAs, UMI PHB, Koni Str.t/Koni SA, C5 Z06 front / LS1 F-body rear brake swap, factory hurst with short stick
2014 2LT Cruze 2.0 Turbo Diesel
|
|
|
08-15-2015, 05:36 PM
|
#79
|
Join Date: Apr 2015
Location: Sicklerville,NJ
Posts: 142
|
Yes the hammer and socket was the only way that bushing was going in. I just took it around the block and the clutch feels great. I wanted the car to warm up to check for leaks at the bajo bolts and I noticed my oil pressure gauge is now reading 0. Ugh Did I hit the pressure switch with a wrench and break it. Yes there is oil in the car
|
|
|
08-15-2015, 05:44 PM
|
#80
|
Join Date: Apr 2015
Location: Sicklerville,NJ
Posts: 142
|
I did notice that the black body was loose on the pressure switch by loose I mean it moves in and out. Just the black plastic.
|
|
|
08-17-2015, 12:27 PM
|
#81
|
Join Date: Apr 2015
Location: Sicklerville,NJ
Posts: 142
|
Ok its back and running and reading oil pressure now. Thanks for all of your help guys. Yes you were correct Thor
|
|
|
08-17-2015, 01:16 PM
|
#82
|
^^^Lover of bad cars^^^ Meet Coordinator
Join Date: Aug 2007
Location: Whitehouse Station
Posts: 2,255
|
Quote:
Originally Posted by cycomiko
Ok its back and running and reading oil pressure now. Thanks for all of your help guys. Yes you were correct Thor
|
__________________
1986 Honda VFR750 - 89.3HP to the wheel
2000 Trans Am M6 - Mods: Yes.
2018 Durango R/T - AFE Intake, JLT Catch Can, Stainless Works Catback, Vinyl Dodge Racing Stripes
2003 Toyota Matrix XRS M6 - Lol
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|