 |
11-15-2010, 10:53 AM
|
#1
|
Join Date: Oct 2004
Location: Hillsdale, NJ
Posts: 168
|
TH400 and other 2nd gen parts for sale
I am parting a 79 trans am and I have alot let over
TH400 - $200
Interior parts Ask there are to many to list
2 Rally rims $25 ea
Front nose assembly (Everything lights metal, plate, emblem, etc) $200
Amber side lights $25 ea
Bezels for the amber lights $10 ea
Rear tail lights (the whole set up with gas tank door) $75
Front suspension $100 for all of it A arms, springs shocks sway bars etc
Inner fenders $50
Lots of gauges vents relays wiring harnessess please just ask!! If you want pm, email me or shoot me you # and I will call you when I have a chance.
Eric
__________________
1998 Transam Chameleon -- SOLD
1981 Trans am Pontiac 400, TH350 -In progress
Bored .060 over, speed pro forged pistons, cat H braun rods, STOCK CRANK CUT .010 .010, ROLLER timing chain, melling 60lb oil pum, comp lifters, comp push rods .080 wall, speed pro molly rings, #62 heads fully ported, stainless valves 2.11X1.77,comp springs and retainers, clevitte bearings, Melling SPC-7 camshaft RAIII, QJ carb 700 cfm
Last edited by transamws686; 11-29-2010 at 11:58 AM.
Reason: Parts added
|
|
|
|
11-15-2010, 05:07 PM
|
#2
|
|
13 Second Club
Join Date: Feb 2007
Posts: 875
|
color of interior parts??
__________________
yes, my hog is bigger then yours
|
|
|
|
|
11-15-2010, 05:34 PM
|
#3
|
Join Date: Oct 2004
Location: Hillsdale, NJ
Posts: 168
|
They are black
__________________
1998 Transam Chameleon -- SOLD
1981 Trans am Pontiac 400, TH350 -In progress
Bored .060 over, speed pro forged pistons, cat H braun rods, STOCK CRANK CUT .010 .010, ROLLER timing chain, melling 60lb oil pum, comp lifters, comp push rods .080 wall, speed pro molly rings, #62 heads fully ported, stainless valves 2.11X1.77,comp springs and retainers, clevitte bearings, Melling SPC-7 camshaft RAIII, QJ carb 700 cfm
|
|
|
|
|
11-29-2010, 11:58 AM
|
#4
|
Join Date: Oct 2004
Location: Hillsdale, NJ
Posts: 168
|
TH400 - $200
Non-tilt steering column blash $75
Cowl panel screen - $10
Wiper switch - $15
"Y" defrost duct $40
Door jam vents $5
Hood hinges $15 each
Window Trim $40 (have front and rear)
Metal panel that goes over the trunk under the rear window $
Cig lighter $10
Dash board brace under steering wheel $10
Dash vents $5
Glove box $20
Driver side air duct $20
Passenger side air duct $20 ea
Side marker light bezels $10 ea
Side marker lights $15
79-81 Rear tail light section and gas tank door $50
Whiper arms - $20 ea
Driver fender $100
Master cylinder, Brake boster $50
used sail panel red dyed black - $50
roof trim non t-top 2 plastic y-pieces and the front and back metal $100
upper seat belt covers, $50
Driver side arm rest $25
79-81 Front bumber, metal, head lights, pontiac emblem, etc, just need to bolt up to car $200
RTS dash emblem $20 each
78 Air cleaner assembly $150 From a 400 (bought it from a member here)
75 shaker scoop part of base craked off and is cut out, $40
Seat track trim plate $10 ea
power window covers $20 ea
inner door plastic hndle trim
Bezels that go around the gauges
if you need a part ask I may have it. make offers
__________________
1998 Transam Chameleon -- SOLD
1981 Trans am Pontiac 400, TH350 -In progress
Bored .060 over, speed pro forged pistons, cat H braun rods, STOCK CRANK CUT .010 .010, ROLLER timing chain, melling 60lb oil pum, comp lifters, comp push rods .080 wall, speed pro molly rings, #62 heads fully ported, stainless valves 2.11X1.77,comp springs and retainers, clevitte bearings, Melling SPC-7 camshaft RAIII, QJ carb 700 cfm
|
|
|
|
|
11-29-2010, 04:12 PM
|
#5
|
Join Date: Mar 2010
Location: Winslow
Posts: 71
|
Hey,
I didn't see you post it, but do you by chance have the pass side fender?
Steve
|
|
|
|
|
11-29-2010, 04:56 PM
|
#6
|
Join Date: Oct 2004
Location: Hillsdale, NJ
Posts: 168
|
I have the passenger fender but it is only good for donor metal. The bottom is rusted out
__________________
1998 Transam Chameleon -- SOLD
1981 Trans am Pontiac 400, TH350 -In progress
Bored .060 over, speed pro forged pistons, cat H braun rods, STOCK CRANK CUT .010 .010, ROLLER timing chain, melling 60lb oil pum, comp lifters, comp push rods .080 wall, speed pro molly rings, #62 heads fully ported, stainless valves 2.11X1.77,comp springs and retainers, clevitte bearings, Melling SPC-7 camshaft RAIII, QJ carb 700 cfm
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
