|
03-23-2010, 02:37 PM
|
#1
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
11.04 @ 122 - Stupid LT1!!
I'm so close to 10s...it's driving me nuts.
Went to Cecil County Raceway in MD on Friday night. Had good air (about 60-degrees at the time of the two runs I did make before getting booted for no cage) and okay track prep.
On Thursday, I finished the install of my Wolfe rear solid swaybar, which, IMO, is hands down the best suspension modification a drag racer could do. When properly adjusted, the car leaves straight as an arrow. Before, I had alot of left-hand pull while the car meandered down the track. That's a thing of the past. 60's tonight were 1.54 and 1.57 (best to date is a 1.52) respectively, spinning just a bit each time.
Someone else filmed the 11.04 run, so I'll post the vid of that once it's available. Here's a video of the second run of the night, an 11.11.
http://www.youtube.com/watch?v=x2cizjJ-qGY
For those that don't know, the car is an AI heads/cam/383 + bolt-ons through a 4L60E and Ford 9". Still untuned (mail-order only) and still under-geared.
|
|
|
03-23-2010, 02:38 PM
|
#2
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
Geez, what a slow car.
Throw a 50 shot at it!
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
03-23-2010, 02:43 PM
|
#3
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
Quote:
Originally Posted by LTs1ow
Geez, what a slow car.
Throw a 50 shot at it!
|
That's not till NEXT year.
Honestly just going to Atco should get me an extra tenth!
|
|
|
03-23-2010, 03:06 PM
|
#4
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
that car is very impressive! would you mind expanding on your setup? you can pm me if you like. just wondering what rotating assembly, gear ratio, tire size, trans parts, etc. basically everything to make it go fast
|
|
|
03-23-2010, 03:20 PM
|
#5
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
Quote:
Originally Posted by sweetbmxrider
that car is very impressive! would you mind expanding on your setup? you can pm me if you like. just wondering what rotating assembly, gear ratio, tire size, trans parts, etc. basically everything to make it go fast
|
I have no secrets, sure. Here's the list:
Ohio 4340 forged 1-piece RMS 3.75" stroke crank
Forged Scat 6" I-beam rods
Forged JE -5cc flat-tops
Zero-decked, 4-bolt factory LT1 block with modified oil gallies
Canton 7qt 242T oil pan
Melling 10552 high volume/pressure pump
Advanced Induction 200cc cylinder heads
Crane Gold 1.6 rockers, beehive springs
Custom grind AI hydraulic roller cam (23x/24x, .60x" on a 108 LS).
AI ported intake manifold (powdercoated green... )
42# Lucas/Delphi injectors
Stock fuel pressure regulator and lines
Walbro 255lph fuel pump/Racetronix harness
LPP stainless steel stepped headers
Hooker cat-back with a Quicktime electric cutout
CSI electric water pump
Holley 58mm throttle body
Factory ram air box, factory untouched MAF
BMR boxed LCAs, PHR
Spohn torque arm, chassis mount
Ford 9", full spool, 3.90 gears with Wilwood rear brakes
Weld Pro Stars front/rear - 165s front, 26x10.5x15" rear.
Wolfe solid rear swaybar
PCMforless.com mail-order tune
And I think that's about it...maybe.
Last edited by RamAir95TA; 03-23-2010 at 03:27 PM.
|
|
|
03-23-2010, 03:24 PM
|
#6
|
Join Date: Aug 2005
Posts: 218
|
Quote:
Originally Posted by RamAir95TA
...Wolfe rear solid swaybar, which, IMO, is hands down the best suspension modification a drag racer could do.
|
I have to agree. This really makes the car go up and out straight. IMO Cecil is a bit quicker that Atco. I'm usually a .10 quicker at Cecil.
__________________
'95 Pontiac Formula
Blue-Green Chameleon
LT1 Auto
'07 Ford Mustang GT Alloy Metallic
4.6 Auto, 3.73 gears, C&L CAI, Diablo 91 octane tune, drag radials, and a saftey loop. What else do I need for a 14 second bracket car?
|
|
|
03-23-2010, 03:26 PM
|
#7
|
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,676
|
Nice runs! What converter are you running?
__________________
John
|
|
|
03-23-2010, 03:33 PM
|
#8
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
Quote:
Originally Posted by Featherburner
Nice runs! What converter are you running?
|
It's a custom Performabuilt 4000, but will likely get pulled for a larger Yank.
|
|
|
03-23-2010, 03:47 PM
|
#9
|
Join Date: Aug 2005
Posts: 218
|
Wolf makes a nice roll bar too. I don't have a cage just an 8 point roll bar with swing outs in my car. I'm good to run as quick as 10.0. I believe you only need a 5 point bar to run that fast.
__________________
'95 Pontiac Formula
Blue-Green Chameleon
LT1 Auto
'07 Ford Mustang GT Alloy Metallic
4.6 Auto, 3.73 gears, C&L CAI, Diablo 91 octane tune, drag radials, and a saftey loop. What else do I need for a 14 second bracket car?
|
|
|
03-23-2010, 04:30 PM
|
#10
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
Quote:
Originally Posted by kazman
Wolf makes a nice roll bar too. I don't have a cage just an 8 point roll bar with swing outs in my car. I'm good to run as quick as 10.0. I believe you only need a 5 point bar to run that fast.
|
Yeah, I have the 6-point Wolfe weld-in bar ready to go, just need to have it welded in.
|
|
|
03-23-2010, 04:56 PM
|
#11
|
8 Second Club
Join Date: Jun 2006
Posts: 4,315
|
damn oh so close joe!! next time bro. good job
|
|
|
03-23-2010, 06:01 PM
|
#12
|
Join Date: Dec 2004
Location: manchester, NJ
Posts: 1,775
|
man that car is fast... congratulations on the new best though...
__________________
97 Firebird Formula - 383LT1
15 Subaru WRX - 2.0L-turbo
|
|
|
03-23-2010, 06:15 PM
|
#13
|
Guest
|
well race motor to motor when i get home Joe, then spray to spray next season
|
|
|
03-23-2010, 06:37 PM
|
#14
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
Thanks for the write up on the mods! definitely got me thinkin
is it a performabuilt trans? stage 2?
|
|
|
03-23-2010, 06:48 PM
|
#15
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
Quote:
Originally Posted by sweetbmxrider
Thanks for the write up on the mods! definitely got me thinkin
is it a performabuilt trans? stage 2?
|
Yessir, stage 2!
|
|
|
03-23-2010, 08:00 PM
|
#16
|
Join Date: Jan 2006
Location: Old Bridge
Posts: 133
|
Car sounds awesome. Congrats on the new best.
__________________
My buddy rob:
"fords are always breaking thats why I have a chevy to tow it"
|
|
|
03-23-2010, 08:35 PM
|
#17
|
Join Date: Apr 2008
Location: Brick
Posts: 149
|
wOW !! Thats Moving !! Tweak that tune and your in the 10's
__________________
1998 CAMARO Z28 A4*STOCK *STALLED & GEARED *
|
|
|
03-23-2010, 09:28 PM
|
#18
|
11 Second Club
Join Date: Feb 2008
Location: Edison, NJ
Posts: 4,619
|
How do you like that trans?
I'm thinking of going with theyre setup... Why are you pulling the stall?
__________________
1999 Z28 Convertible. 6 speed swap, wide cowl hood, full hockey stripes, and a whining 10 bolt.
2008 Sierra Vortec Max. 6.2 swapped, headers, Magnaflow catback, GMPP CAI, NHT optioned tow package.
2006 GTO, 11.48 @ 118.3
|
|
|
03-23-2010, 09:29 PM
|
#19
|
Join Date: Jan 2010
Location: Shamong, NJ
Posts: 1,358
|
Very nice pass, a little spray and you are definitely there
__________________
1969 Camaro SS - 350 w/ some work done.
2010 F-150
|
|
|
03-24-2010, 03:43 AM
|
#20
|
I <3 sheep
Join Date: Mar 2005
Location: Belmar
Posts: 4,907
|
Quote:
Originally Posted by RamAir95TA
Advanced Induction 200cc cylinder heads
Custom grind AI hydraulic roller cam (23x/24x, .60x" on a 108 LS).
AI ported intake manifold (powdercoated green... )
|
How awesome is the AI stuff
__________________
Quote:
Originally Posted by Tru2Chevy
Steve has a thing for sheep....
|
'78 Big Wheel- 2FWFP
|
|
|
03-24-2010, 06:53 AM
|
#21
|
Guest
|
Quote:
Originally Posted by SteveR
How awesome is the AI stuff
|
almost as good as my LE stuff
|
|
|
03-24-2010, 11:25 AM
|
#22
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
yut yo...
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
03-24-2010, 03:54 PM
|
#23
|
Guest
|
haha i respect both AI and LE, both have proven that they can produce results. i just like breaking balls
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|