![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
08-26-2012, 01:04 PM
|
#1
|
Join Date: Jun 2006
Location: Old Bridge, NJ
Posts: 932
|
no oil pressure at hot idle
So i've been chasing a no oil pressure issue (at least on my cluster) on my 95 lt1. This happened out of the blue one day as i stopped at a light. Since then, i've replaced the sending unit sensor, and today I changed the oil filter, and put in 10w40, hoping the thicker oil would make a difference. I also just happened to notice that if I bring the car up to 2k my speedo climbs up between 5-10mph kind going back and forth. Idk if maybe the cluster is going bad, and I have no issue at all with my oil pressure?
Also if I bring the car up to 2k i'm reading about 20psi. Another note, the engine doesnt tap or knock at all when cluster reads 0psi.
__________________
|
|
|
08-26-2012, 01:54 PM
|
#2
|
Join Date: Dec 2008
Location: Garwood NJ
Posts: 221
|
First thing to do would be to verify oil pressure using a mechanical gauge. You need to figure out if it is an electrical or mechanical problem. Once you verify if the oil pressure is actually zero or not, post the results and it will make it easier to diagnose.
__________________
Artie
73 Camaro 25.3 build TT LS in progress
67 Camaro
99 T/A
Other crap not worth mentioning
|
|
|
08-26-2012, 05:20 PM
|
#3
|
12 Second Club / Bullwinkle
Join Date: Oct 2010
Location: Old Bridge, NJ/Corpus Christi, TX
Posts: 1,847
|
Agreed. Use a mechanical gauge. Something might have broke in the cluster. Is the motor knocking at all?
__________________
1994 Medium Patriot Red Z28 6spd
370ci/Huron Speed T6 S480 ET-R HO
Quote:
Originally Posted by Jersey Mike
Quote:
Originally Posted by WSex
who is FFB?
|
An NJFBOA legend. Ask about him at the next meet.
|
|
|
|
08-27-2012, 10:50 AM
|
#4
|
Sliderule / Moderator
Join Date: Oct 2004
Location: Catawissa PA
Posts: 2,294
|
How many miles? LT1 are notorious for low oil pressure. 10-12 PSI at idle is actually common, lower then that and over 100K miles you are probably looking at a new new oil pump or replacing the pump spring.
__________________
93Z M6 Black: The 385 Lives! Supercharged, 3-core front mount intercooler, GTP heads, 3:73's, Street twin clutch, Jethot Longtubes, Mufflex 4" catback/spintech, S+W cage, Spohn Suspenion, Yada Yada Yada
1) Build it
2) Race it
3) Break it
4) Repeat!!!
|
|
|
08-27-2012, 05:07 PM
|
#5
|
Join Date: Jun 2006
Location: Old Bridge, NJ
Posts: 932
|
motor doesn't knock at all. Car has 141k. I just replaced all the gaskets on the engine. New timing chain set, new distributor. Pressure was fine for the first 500 miles after I replaced everything.
__________________
|
|
|
08-27-2012, 05:28 PM
|
#6
|
Join Date: Sep 2006
Location: north jersey
Posts: 1,680
|
As stated in a previous post, first thing is to run a mechanical gauge and see what psi it reads then go from there
|
|
|
08-31-2012, 08:00 AM
|
#7
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
Believe it or not ALLDATA says that that normal LT1 oil PSI at hot idle is 7-10 PSI. that was odd for me coming from the school of SBC's need at leat 30-40 PSI. I would do as stated above
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
Last edited by greenformula92; 08-31-2012 at 08:00 AM.
|
|
|
08-31-2012, 09:11 AM
|
#8
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,149
|
Quote:
Originally Posted by greenformula92
Believe it or not ALLDATA says that that normal LT1 oil PSI at hot idle is 7-10 PSI. that was odd for me coming from the school of SBC's need at leat 30-40 PSI. I would do as stated above
|
SBC do not need 30-40 psi at idle. the old rule of thumb was basically 10psi per 1000 rpm.
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
08-31-2012, 09:22 AM
|
#9
|
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,634
|
Have you put a mechanical gauge on it yet?
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41
Quote:
Originally Posted by Blackbirdws6
I can appreciate a dream but this person needed some real friends.
|
|
|
|
08-31-2012, 11:36 AM
|
#10
|
Join Date: Aug 2005
Location: Blackwood, NJ
Posts: 2,295
|
My 95 LT1 use to idle @ 5psi and @ WOT was around 40psi.. It had 73,000 miles on it..
__________________
Jeff
2002 WS6 T/A.. M6..Built 383 TMR tune..461rwhp,458rwtq
2009 G8 GT. Bone stock 13.6@103.. Vararam Intake, GXP Axlebacks, LS2 FRC's
1998 Corvette Convertible, Vararam Intake+Power Duct, Fast 90/90, Ti Axleback..12.8@110
2003 Cobra Convertible 10th Anniversary
http://www.fquick.com/slow-v6
Local car cruise schedule..
http://www.cliffscalendar.com/
|
|
|
09-01-2012, 02:41 AM
|
#11
|
12 Second Club
Join Date: Aug 2004
Location: Oradell
Posts: 8,368
|
i have the same issue... after much reading ive concluded its just an LT1 thing. 145k miles on my LT1 and at hot idle it drops down to just about nothing on the gauge, but if u tap the gas it jumps back up
also i replaced the presure sensor when i did the manifold gaskets and thats when i first noticed it being low, so it could be a ****** sensor i bought
__________________
86 Camaro
88 Camaro
95 Impala SS
97 Trans Am WS6
98 Blazer ZR2
00 Corvette
04 CTS-V
07 Sublime Charger Daytona
10 Tahoe SSV
12 Tahoe LT
17 Malibu LT
Last edited by maroman88; 09-01-2012 at 02:45 AM.
|
|
|
09-01-2012, 07:20 AM
|
#12
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
Probably due to wear on the bearings and a tired oil pump. A high pressure spring will definitely help.
|
|
|
09-15-2012, 05:16 PM
|
#13
|
Join Date: Jun 2006
Location: Old Bridge, NJ
Posts: 932
|
haven't had time to get a gauge on there yet. work's been crazy busy lately and by the time i get home i don't want to move, lol. keep you guys updated though.
__________________
|
|
|
09-17-2012, 02:06 PM
|
#14
|
Join Date: Jun 2006
Location: Old Bridge, NJ
Posts: 932
|
so i finally got a gauge on the car. At hot idle i'm reading 2-4 psi. and at 2k rpm, i'm reading between 22-24.
__________________
|
|
|
09-17-2012, 06:29 PM
|
#15
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
Yeah, that's not good. I'm sure a rod/main bearing is on its way out already.
|
|
|
09-24-2012, 10:51 AM
|
#16
|
Join Date: Jun 2006
Location: Old Bridge, NJ
Posts: 932
|
So where do I go from here? Lol
__________________
|
|
|
09-24-2012, 11:04 AM
|
#17
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
Rebuild the bottom end now or later. At least do a gm white spring in the oil pump.
|
|
|
09-24-2012, 12:14 PM
|
#18
|
Join Date: Dec 2008
Location: Garwood NJ
Posts: 221
|
To fix it right, freshen up the rotating assembly. Might be able to band aid it with a new oil pump to get a little more time out of it, but if the oil pressure is that low now, the damage is already done.
__________________
Artie
73 Camaro 25.3 build TT LS in progress
67 Camaro
99 T/A
Other crap not worth mentioning
|
|
|
09-26-2012, 10:00 PM
|
#19
|
Join Date: Jul 2011
Location: harmony, nj (phillipsburg)
Posts: 513
|
acceptable range hot idle as stated from gm is 6-12 psi at the lowest. i read that somewhere i think on a vette forum.
that sucks though, good luck man
__________________
1994 Firebird Formula - Injuneer's car - NEW PB 9.90 @131
2021 Charger Scat
Wrench/driver 94 Camaro Ellwein 385/D1SC/CPT 4l60e/9" slow pile
Last edited by townsend; 09-26-2012 at 10:00 PM.
|
|
|
01-02-2013, 04:52 PM
|
#20
|
Join Date: Jul 2009
Location: Bridgeport NJ
Posts: 165
|
Considering the oil pressure was a problem only after you changed your gaskets (which ones did you change and why?) it would lead me to believe that perhaps you contaminated the engine/oil pan/etc.
|
|
|
01-05-2013, 02:46 PM
|
#21
|
Sliderule / Moderator
Join Date: Oct 2004
Location: Catawissa PA
Posts: 2,294
|
I would put in the pump / spring. I've done this on a few cars and it does bring the oil pressure up to where it needs to be.
Here is an old thread that gives the part numbers.
http://www.njfboa.org/forums/showthr...eferrerid=1095
__________________
93Z M6 Black: The 385 Lives! Supercharged, 3-core front mount intercooler, GTP heads, 3:73's, Street twin clutch, Jethot Longtubes, Mufflex 4" catback/spintech, S+W cage, Spohn Suspenion, Yada Yada Yada
1) Build it
2) Race it
3) Break it
4) Repeat!!!
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|