![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
|
11-15-2012, 10:19 PM
|
#1
|
Join Date: Jun 2011
Location: Voorhees Nj
Posts: 217
|
no power?
i just put my car back together(89 formula) and the car feels like it doesn't wanna move..like a rock. It's a 5 speed manual..and it feels like it's reved out all the way when you try to move it..like something is holding it.. It wasn't like that before the distributor and coil were removed..and now the temp gauge and radiator fan aren't working..i'm unsure if the temp gauge could be a fuse? and is causing the fan not to come on? The no power could possibly be timing? Any suggestions where to start?
__________________
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
![](https://sphotos-a.xx.fbcdn.net/hphotos-ash4/423616_10151064900398364_1590046500_n.jpg)
1989 Formula
1986 T/A
Attempting to race old junk since 2009 ![ROFL](http://www.njfboa.org/forums/images/smilies/rofl.gif)
~Jamie
Last edited by Phoenixfire1989; 11-15-2012 at 10:25 PM.
|
|
|
11-16-2012, 07:45 AM
|
#2
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,899
|
Why did you remove the coil and distributor?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
Last edited by LTb1ow; 11-16-2012 at 08:53 AM.
|
|
|
11-16-2012, 08:54 AM
|
#3
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
What makes you think the temp gauge and fan are not working? It's cold outside now.
Does the car have a thermostat?
As for the no power, if the timing was not re-set after the distributor was installed you could certainly be down on power.
|
|
|
11-16-2012, 08:59 AM
|
#4
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
I think the one rear drum is locked up for sitting so long, there is a drag mark from the RR tire in my driveway from the car going onto the flatbed
|
|
|
11-16-2012, 09:01 AM
|
#5
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,899
|
Why would a tire have to do with the engine revving and not going anywhere?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
11-16-2012, 09:20 AM
|
#6
|
Lord of the rings / 10 Second Club / Meet Coordinator
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,357
|
Quote:
Originally Posted by LTb1ow
Why would a tire have to do with the engine revving and not going anywhere?
|
If the dizzy was touched then I would point to that first. If something is dragging, it will make it feel like something is holding it back. Prob feels like driving with the parking brake on.
__________________
97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140
'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
|
|
|
11-16-2012, 09:23 AM
|
#7
|
Join Date: Aug 2005
Location: Blackwood, NJ
Posts: 2,295
|
Throttle Body not opening or stuck?
__________________
Jeff
2002 WS6 T/A.. M6..Built 383 TMR tune..461rwhp,458rwtq
2009 G8 GT. Bone stock 13.6@103.. Vararam Intake, GXP Axlebacks, LS2 FRC's
1998 Corvette Convertible, Vararam Intake+Power Duct, Fast 90/90, Ti Axleback..12.8@110
2003 Cobra Convertible 10th Anniversary
http://www.fquick.com/slow-v6
Local car cruise schedule..
http://www.cliffscalendar.com/
|
|
|
11-16-2012, 09:40 AM
|
#8
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by Blackbirdws6
If the dizzy was touched then I would point to that first. If something is dragging, it will make it feel like something is holding it back. Prob feels like driving with the parking brake on.
|
The car feels like it hits the limiter at 3000 rpm, and also pops and backfires. Im almost positive the brakes are not locked, the car rolls just fine. It does seem to have a pretty large exhaust leak that idk how close it is to the 02 sensor, so that may be contributing to it as well.
Quote:
Originally Posted by Slow-V6
Throttle Body not opening or stuck?
|
Nope, working properly.
I dont know much about 80's computer stuff, I know you have to unplug one of the connectors for the computer to set base timing, but the car also doesnt have a timing scale on it so its kinda just by ear at the moment.
Quote:
Originally Posted by WildBillyT
What makes you think the temp gauge and fan are not working? It's cold outside now.
Does the car have a thermostat?
As for the no power, if the timing was not re-set after the distributor was installed you could certainly be down on power.
|
The fact that they are not working makes me think that ![Knee Slapper](http://www.njfboa.org/forums/images/smilies/kneeslap.gif) the car definatly gets HOT but the gauge reads nothing and the fan never kicks on, there is a terminal next to the battery that has some pretty high resistance and corrosion from sitting, which would partly explain the fans, and the sensor reads the proper OHMS at temps. The gauge itself has power to it, just not getting signal. Yes the car has a t-stat. Im also assuming that the fans need temp sensor input to kick on?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-16-2012, 09:42 AM
|
#9
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,899
|
Wait, who are you? Does your car do the same thing, maybe its a third gen thing?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
11-16-2012, 09:49 AM
|
#10
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by B4C
The car feels like it hits the limiter at 3000 rpm, and also pops and backfires. Im almost positive the brakes are not locked, the car rolls just fine. It does seem to have a pretty large exhaust leak that idk how close it is to the 02 sensor, so that may be contributing to it as well.
Nope, working properly.
I dont know much about 80's computer stuff, I know you have to unplug one of the connectors for the computer to set base timing, but the car also doesnt have a timing scale on it so its kinda just by ear at the moment.
The fact that they are not working makes me think that ![Knee Slapper](http://www.njfboa.org/forums/images/smilies/kneeslap.gif) the car definatly gets HOT but the gauge reads nothing and the fan never kicks on, there is a terminal next to the battery that has some pretty high resistance and corrosion from sitting, which would partly explain the fans, and the sensor reads the proper OHMS at temps. The gauge itself has power to it, just not getting signal. Yes the car has a t-stat. Im also assuming that the fans need temp sensor input to kick on?
|
There is your place to start. Nowhere else. This engine probably has a bad tune at the moment.
|
|
|
11-16-2012, 09:56 AM
|
#11
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by LTb1ow
Wait, who are you? Does your car do the same thing, maybe its a third gen thing?
|
Im the one working on the car
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-16-2012, 09:57 AM
|
#12
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by WildBillyT
There is your place to start. Nowhere else. This engine probably has a bad tune at the moment.
|
I ordered one just waiting on it in the mail. I think I may be a tooth off on the dizzy.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-16-2012, 10:16 AM
|
#13
|
Stalker
Join Date: Aug 2004
Posts: 12,077
|
Quote:
Originally Posted by B4C
I ordered one just waiting on it in the mail. I think I may be a tooth off on the dizzy.
|
doubt it, it'd be on, or 180 out. if anything you have the dizzy turned too far one way or the other.
And keep in mind you'll have to go through the process of finding TDC(compression, not exhaust stroke) then setting the dizzy to #1, Then adjust timing.
|
|
|
11-16-2012, 10:17 AM
|
#14
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
Sounds like too many hands in the pot and none of them are fully addressing all of the known and unknown problems.
|
|
|
11-16-2012, 10:22 AM
|
#15
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Am I correct on pulling the connector to set base timing? One wire connector, brown with a black stripe?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-16-2012, 10:23 AM
|
#16
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by B4C
Am I correct on pulling the connector to set base timing? One wire connector, brown with a black stripe?
|
Yes
Last edited by PolarBear; 11-16-2012 at 10:23 AM.
|
|
|
11-16-2012, 10:53 AM
|
#17
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by sweetbmxrider
Sounds like too many hands in the pot and none of them are fully addressing all of the known and unknown problems.
|
I just feel mentally challenged with all this distributor and tbi stuff, its like an alien to me. Silly third gens
Quote:
Originally Posted by PolarBear
Yes
|
Thanks I thought that was the right one just wasn't sure.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
Last edited by B4C; 11-16-2012 at 10:54 AM.
|
|
|
11-16-2012, 11:09 AM
|
#18
|
11 second club / Moderator
Join Date: Aug 2004
Location: West Berlin, NJ
Posts: 7,148
|
There is no timing tab on the riming cover? The crank hub has a black line for your reading
__________________
2001 Trans Am WS6 •SLP Loudmouth II •UMI Suspension •12.857 @ 109.57
1996 Trans Am WS6 •Pacesetter Longtubes •Strange 12 Bolt •Spohn Suspension •11.152 @ 123.85
|
|
|
11-16-2012, 11:12 AM
|
#19
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Correct, has the line on the balancer but no tab.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-16-2012, 11:17 AM
|
#20
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
You can add timing tape and an adjustable pointer.
|
|
|
11-16-2012, 12:40 PM
|
#21
|
Join Date: Aug 2005
Location: Blackwood, NJ
Posts: 2,295
|
be done with it and convert it to a opti! why was the dizzy pulled in the 1st place? is the temp sensor and fan connector located near the dizzy?maybe they got unplugged?
__________________
Jeff
2002 WS6 T/A.. M6..Built 383 TMR tune..461rwhp,458rwtq
2009 G8 GT. Bone stock 13.6@103.. Vararam Intake, GXP Axlebacks, LS2 FRC's
1998 Corvette Convertible, Vararam Intake+Power Duct, Fast 90/90, Ti Axleback..12.8@110
2003 Cobra Convertible 10th Anniversary
http://www.fquick.com/slow-v6
Local car cruise schedule..
http://www.cliffscalendar.com/
Last edited by Slow-V6; 11-16-2012 at 12:44 PM.
|
|
|
11-16-2012, 12:46 PM
|
#22
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,899
|
Quote:
Originally Posted by Slow-V6
be done with it and convert it to a opti! why was the dizzy pulled in the 1st place? is the temp sensor and fan connector located near the dizzy?maybe they got unplugged?
|
This is some solid advice, optisparks are dependable and non adjustable.
+2 on why the dizzy was pulled, did something fall in there? Is this the car with the broken torque converter? Maybe the PCM is doing something weird cause the bearings are shot?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
11-16-2012, 12:51 PM
|
#23
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by Slow-V6
be done with it and convert it to a opti! why was the dizzy pulled in the 1st place? is the temp sensor and fan connector located near the dizzy?maybe they got unplugged?
|
It was removed inorder to be tested in another car to verify a no-start. Convert to opti....put even junkier junk in there? LOL I would be ripping it a out and converting to an ls1 if it were my car.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
Last edited by B4C; 11-16-2012 at 12:54 PM.
|
|
|
11-16-2012, 12:54 PM
|
#24
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,132
|
Quote:
Originally Posted by LTb1ow
This is some solid advice, optisparks are dependable and non adjustable.
+2 on why the dizzy was pulled, did something fall in there? Is this the car with the broken torque converter? Maybe the PCM is doing something weird cause the bearings are shot?
|
This is an 89 formula 5 speed not her 86 trans am.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
11-16-2012, 01:12 PM
|
#25
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,899
|
Ohh ok, so, was it running better before the distributor came out?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|