|
10-02-2017, 11:56 AM
|
#1
|
Hippy Mod, Bergermeister Meisterberger, Moderator
Join Date: Aug 2004
Location: Ewing
Posts: 6,213
|
Oil pan gasket for 86 on up 350
So the ZZ3 motor in my jet boat is leaking oil around the oil pan gasket where it meets the timing cover. It has a metal timing cover, not plastic like some of the ZZ4 motors have. There is no room to drop the pan in the boat so I need to pull the motor out to do it. I've been reading about people leaving the new gasket dry vs putting some sealant on the corners. I ordered the Fel-pro 1 piece gasket and I think the installation instructions say to leave it dry. Anybody have good or bad experience with or without sealant? I can't see any sign of there being sealant on the corners so it might be the original pan gasket from the factory.
__________________
69 Z28 JL8 4 wheel disc brakes - being restored
09 Silverado Z71
|
|
|
10-02-2017, 05:45 PM
|
#2
|
Join Date: Jun 2016
Location: Millstone
Posts: 142
|
I put rtv on the the corners where timing cover and rms housinf meets the block. I used to use international rtv but now im using ford ta-31 rtv
|
|
|
10-03-2017, 11:57 AM
|
#3
|
Hippy Mod, Bergermeister Meisterberger, Moderator
Join Date: Aug 2004
Location: Ewing
Posts: 6,213
|
I just found out that there is oil leaking out from around the oil pan drain plug as well. That looks like where the majority of the oil is coming from. There is definitely some oil dripping from around the timing cover and pan gasket but if the drain plug is the big issue, it should be easier (assuming the pan isn't messed up) to address that first and hold off on the pan gasket until next season.
__________________
69 Z28 JL8 4 wheel disc brakes - being restored
09 Silverado Z71
|
|
|
10-03-2017, 12:19 PM
|
#4
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,152
|
if you need a pan i might have one
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
10-03-2017, 01:10 PM
|
#5
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
I definitely have a one piece RMS SBC pan too
|
|
|
10-04-2017, 02:55 PM
|
#6
|
Hippy Mod, Bergermeister Meisterberger, Moderator
Join Date: Aug 2004
Location: Ewing
Posts: 6,213
|
Well that was fun draining the oil. I have one of those vacuum pumps to pull oil through the dipstick tube but it only pulled about a quart out. I couldn't get the tube to go down any further so that doesn't make much sense unless the pan has some baffling that I don't know about. I put a tinfoil pan under the engine and drained some oil about 1/2 quart at a time and then had to vacuum the oil out of the tinfoil pan. Finally got it drained. The pan looks fine. The drain plug has a copper washer/gasket that looks a little worn. So should I get a new copper washer/gasket or get a nylon one?
__________________
69 Z28 JL8 4 wheel disc brakes - being restored
09 Silverado Z71
Last edited by JL8Jeff; 10-04-2017 at 02:58 PM.
|
|
|
10-04-2017, 04:00 PM
|
#7
|
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,640
|
Personally, I'd do a nylon one. Way less torque to get a good seal.
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41
Quote:
Originally Posted by Blackbirdws6
I can appreciate a dream but this person needed some real friends.
|
|
|
|
10-04-2017, 06:06 PM
|
#8
|
Hippy Mod, Bergermeister Meisterberger, Moderator
Join Date: Aug 2004
Location: Ewing
Posts: 6,213
|
I don't like the drain plug, it doesn't look like a stock one so I ordered a plug with the nylon gasket from Napa and it should be in tomorrow morning.
__________________
69 Z28 JL8 4 wheel disc brakes - being restored
09 Silverado Z71
|
|
|
10-05-2017, 07:51 AM
|
#9
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by JL8Jeff
I don't like the drain plug,
|
The plug you'll only see if you take it out of the pan?
|
|
|
10-05-2017, 09:14 AM
|
#10
|
Hippy Mod, Bergermeister Meisterberger, Moderator
Join Date: Aug 2004
Location: Ewing
Posts: 6,213
|
Quote:
Originally Posted by PolarBear
The plug you'll only see if you take it out of the pan?
|
It looks more like a bolt than a drain plug, it doesn't have the shoulder to it which helps in sealing. It is magnetic though.
__________________
69 Z28 JL8 4 wheel disc brakes - being restored
09 Silverado Z71
|
|
|
10-05-2017, 09:58 AM
|
#11
|
Ebearnezer Scrooge/Power Member/Lips
Join Date: May 2006
Location: Hamilton, Mercer county
Posts: 4,141
|
Quote:
Originally Posted by JL8Jeff
It looks more like a bolt than a drain plug, it doesn't have the shoulder to it which helps in sealing. It is magnetic though.
|
If the washer is thick enough and sealing, it shouldn't really matter. I do like the bolts with flange heads, which I think is what you're wanting?
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|