 |
05-25-2016, 10:41 PM
|
#1
|
Join Date: Feb 2016
Posts: 692
|
broke my poly trans mount t56
Launching at the track tonight broke my prothane poly trans mount. snapped the stud.
it was less than a year old. are these known to fail ?
Is there a better one i can run or should I just stock up on a few of them to swap out quick when they go ?
thanks.
Last edited by 6spdg37s; 05-26-2016 at 06:30 AM.
|
|
|
|
05-26-2016, 09:44 AM
|
#2
|
|
Lord of the rings / 10 Second Club / Meet Coordinator
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,361
|
That's impressive. How hard did it launch? I haven't broken my poly but then again, my car doesn't leave the line that hard. If only the stud snapped I'd say you have some major flex happening somewhere else in the driveline/chassis.
__________________
97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140
'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
|
|
|
|
|
05-26-2016, 09:47 AM
|
#3
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,342
|
Or something was left loose?
|
|
|
|
|
05-26-2016, 09:57 AM
|
#4
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,153
|
Quote:
Originally Posted by sweetbmxrider
Or something was left loose?
|
+1
or are the motor mounts beat?
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
|
05-26-2016, 10:55 AM
|
#5
|
|
13 Second Club / Moderator
Join Date: Jan 2005
Location: Franklin Lakes, NJ
Posts: 8,692
|
When I went to swap out my trans crossmember years back, the mount had wiggled itself loose and was about to fall off. Car was never properly launched either.
|
|
|
|
|
05-26-2016, 03:14 PM
|
#6
|
|
11 Second Club
Join Date: Feb 2008
Location: Edison, NJ
Posts: 4,619
|
Trans mounted torque arm?
__________________
1999 Z28 Convertible. 6 speed swap, wide cowl hood, full hockey stripes, and a whining 10 bolt.
2008 Sierra Vortec Max. 6.2 swapped, headers, Magnaflow catback, GMPP CAI, NHT optioned tow package.
2006 GTO, 11.48 @ 118.3
|
|
|
|
|
05-26-2016, 06:41 PM
|
#7
|
Join Date: Feb 2016
Posts: 692
|
Quote:
Originally Posted by Blackbirdws6
That's impressive. How hard did it launch? I haven't broken my poly but then again, my car doesn't leave the line that hard. If only the stud snapped I'd say you have some major flex happening somewhere else in the driveline/chassis.
|
6k launch
Quote:
Originally Posted by sweetbmxrider
Or something was left loose?
|
no it was tight
Quote:
Originally Posted by BonzoHansen
+1
or are the motor mounts beat?
|
no, new poly motor mounts with about 1000 miles/120 passes on them
Quote:
Originally Posted by NJ Torque
Trans mounted torque arm?
|
yes but ordered the BMR relocation bracket now...
|
|
|
|
|
05-26-2016, 10:11 PM
|
#8
|
Join Date: Sep 2008
Location: Hackettstown, NJ
Posts: 1,650
|
It was the downward pointing stud? May have been overtightened or faulty.
__________________
1998 Z-28 - SLP lid - Ported TB - LS6 Intake - Dynatech SS headers/Catted Y - Magnaflow Exh - 3.42 - Yank SS3600 - UMI weld-in subframe connectors, Adj LCA, Adj PHB, Q1A TA - Bolt-in Relocation Brackets - Strano springs - Koni shocks - 17" C6Z06 wheels - 326HP/335ft-lbs - 12.35 @ 110.41
Quote:
Originally Posted by Blackbirdws6
I can appreciate a dream but this person needed some real friends.
|
|
|
|
|
|
05-27-2016, 06:56 AM
|
#9
|
Join Date: Feb 2016
Posts: 692
|
Quote:
Originally Posted by The_Bishop
It was the downward pointing stud? May have been overtightened or faulty.
|
yes it was. after thinking about it it probably was the shock from the rear thru the torque arm leaving at 6k off the line.
now I am relocating the torque arm ordered the TCC006 from BMR
|
|
|
|
|
05-27-2016, 08:26 AM
|
#10
|
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
6k rpm clutch dumps and please tell me you are not working with a stock torque arm?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
|
|
05-27-2016, 08:34 PM
|
#11
|
Join Date: Feb 2016
Posts: 692
|
Quote:
Originally Posted by LTb1ow
6k rpm clutch dumps and please tell me you are not working with a stock torque arm?
|
no i have bmr adjustable
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
