 |
05-04-2015, 09:08 PM
|
#1
|
|
Resident Camera Guy
Join Date: Aug 2004
Location: North Jersey
Posts: 10,971
|
Por15/Rust Bullet
I'm looking to do some major rust repair and sealing on my floor pan and am looking to seal it with one of these two coat type products. I have the typical rust pools behind the drivers side seat from an unknown leak and light surface rust just about everywhere else under the carpet.
I've already started to remove all the carpet, and hopefully tomorrow or Wednesday I'll let the interior air dry before I take a wheel and wire brush to everything to prep for some patching over the rear fenders, but how much POR15 will I need to coat the full interior all the way to the trunk? Any pointers?
I also would like to paint the inside of the rear wheel well once I get the patches done.
__________________
|
|
|
|
05-04-2015, 09:33 PM
|
#2
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
I would buy two quarts and see how far that goes.
As far as prep, IMO a wire wheel leaves too smooth a surface. You can use it but I'd scuff the metal up to give it some tooth first. Metal-Ready might work too.
|
|
|
|
|
05-04-2015, 10:02 PM
|
#3
|
|
Resident Camera Guy
Join Date: Aug 2004
Location: North Jersey
Posts: 10,971
|
Bill do you think just a hand held wire brush will do?
I'm planning on chopping off the tabs for the back seats as well so thats why I figured I could do double work with a wheel/brush.
__________________
|
|
|
|
|
05-05-2015, 08:10 AM
|
#4
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,342
|
Jeep guys love both of those products. I bought the whole por15 kit and did up to my back seat area. It held up great, I never even put carpet in. I think I only bought a quart and was able to do a solid pass throughout.
|
|
|
|
|
05-05-2015, 09:45 AM
|
#5
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
Quote:
Originally Posted by ar0ck
Bill do you think just a hand held wire brush will do?
I'm planning on chopping off the tabs for the back seats as well so thats why I figured I could do double work with a wheel/brush.
|
It will clean the surface a bit but probably won't leave it rough enough.
I'd go for a wire wheel in an angle grinder to clean and then something like metal ready to etch. The surface can't be too smooth.
|
|
|
|
|
05-05-2015, 04:32 PM
|
#6
|
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,677
|
I used this on my car trailer top and bottom and it's a little cheaper than POR15 and works as well if not better than POR15. Highly recommended!
http://www.kbs-coatings.com/
__________________
John
|
|
|
|
|
05-07-2015, 09:36 AM
|
#7
|
Join Date: Dec 2009
Location: milltown
Posts: 1,497
|
Quote:
Originally Posted by ar0ck
Bill do you think just a hand held wire brush will do?
I'm planning on chopping off the tabs for the back seats as well so thats why I figured I could do double work with a wheel/brush.
|
do you have a cordless or even corded drill? just stop at HF and get the wire brush drill attachments
http://www.harborfreight.com/wire-wh...-pc-60475.html
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car
1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock  SOLD
1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121
03 Blazer 2 door - salt sponge
|
|
|
|
|
05-08-2015, 01:14 AM
|
#8
|
|
10 Second Club / Meet Coordinator
Join Date: Dec 2004
Location: Roxbury, NJ
Posts: 2,120
|
__________________
1987 IROC-Z - modified
|
|
|
|
|
05-11-2015, 09:17 PM
|
#9
|
Join Date: Oct 2010
Location: deptford nj
Posts: 4
|
Did my floor and trunck of my Z/28 about 10 years ago with por15,still perfect.
I used a hand held sand blaster & rolec discs.used like 2 qts.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
