![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
01-03-2011, 02:16 PM
|
#1
|
Join Date: Jan 2008
Location: Aberdeen,nc/columbus,nj
Posts: 1,449
|
manual fan switch help
hey guys im having an issue with a 94 camaro 3.4 v6 where the cooling fan isnt kicking on when it should be.(not kicking on at all)
i pulled the fan and benched tested it and it will run no problem
replaced the relay and checked all fuses
(was told it should run when the ac is on- didnt run at all)
Update. well i just picked up a fan wiring kit that includes an adjustable temp control i have this pretty much setup ready to go just need some quick info. dont have a wiring diagram for this car so if you know it would be appreicated.
i have to run one wire to the ac clutch wire. ( clutch has 2 wires going to it. looks like green and black?)
second one i need to run is to a switched power source. (cant be pulse signal) if there are any wires close to the battery you know of that is easy to tap into let me know.
__________________
Eric
07 Silverado 1500 5.3
01 Z28 6 speed
Last edited by emolineaux; 01-30-2011 at 03:33 PM.
|
|
|
01-03-2011, 02:25 PM
|
#2
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,150
|
Does the fan trigger via ECM or fan switch in this car?
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
01-03-2011, 02:54 PM
|
#3
|
Join Date: Jan 2008
Location: Aberdeen,nc/columbus,nj
Posts: 1,449
|
Quote:
Originally Posted by BonzoHansen
Does the fan trigger via ECM or fan switch in this car?
|
well its got a coolant temp sensor for the gauge and also has a temp switch in the drivers head, i believe it the switch sends info to the ecm which it than turns fans on.
switch and sensor are only a few months old(changed everthing out when i did waterpump job.)
ive been reading up on this and a bunch of people are having same issue. which could be a bad ecm.
i have to bring my tester home tomorrow to see if i might have a broken wire somewhere.
__________________
Eric
07 Silverado 1500 5.3
01 Z28 6 speed
|
|
|
01-03-2011, 02:58 PM
|
#4
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
If its a similar setup as the V8 cars, which I would imagine it is, the manual fan switch just grounds the fan relay instead of the PCM doing it. So if the relays, fuses and fans all work, you should be good to go with that.
So the two leads, high and low fans, can either be combined or wired separately for individual control. Throw a switch and a good ground in the cabin together, and voila success.
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
Last edited by LTb1ow; 01-03-2011 at 02:59 PM.
|
|
|
01-03-2011, 03:20 PM
|
#5
|
Join Date: Jan 2008
Location: Aberdeen,nc/columbus,nj
Posts: 1,449
|
Quote:
Originally Posted by LTs1ow
If its a similar setup as the V8 cars, which I would imagine it is, the manual fan switch just grounds the fan relay instead of the PCM doing it. So if the relays, fuses and fans all work, you should be good to go with that.
So the two leads, high and low fans, can either be combined or wired separately for individual control. Throw a switch and a good ground in the cabin together, and voila success.
|
na the 3.4 camaros have a different setup all together compaired to the 3.8 and v8 cars.
this has one big single fan. and no plugs like pictured like the v8s do. (if it was the same i would of thrown my slp fan switch in place but of course this is the one model it doesnt fit lol)
__________________
Eric
07 Silverado 1500 5.3
01 Z28 6 speed
|
|
|
01-03-2011, 04:47 PM
|
#6
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
Ach, do'Oh moment for me.
Can you apply the same logic and just piggy back off the PCM control lead to the fan relay?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
01-03-2011, 06:43 PM
|
#7
|
Join Date: Jan 2008
Location: Aberdeen,nc/columbus,nj
Posts: 1,449
|
Quote:
Originally Posted by LTs1ow
Ach, do'Oh moment for me.
Can you apply the same logic and just piggy back off the PCM control lead to the fan relay?
|
i prob could but i was just thinking about making a basically a stand along harness. i have an oem connector off my trans ams harness. was just going to run that through the firewall switch in the dash run a fuse or relay near the battery,
__________________
Eric
07 Silverado 1500 5.3
01 Z28 6 speed
|
|
|
01-04-2011, 04:44 PM
|
#8
|
Stalker
Join Date: Aug 2004
Posts: 12,077
|
run a relay
|
|
|
01-05-2011, 12:35 PM
|
#9
|
Sliderule / Moderator
Join Date: Oct 2004
Location: Catawissa PA
Posts: 2,294
|
Try going to Shoebox's site and look in the schematic section. He has how to do OBDI and ODBII cars. Proabably the same for a V6 or V8.
http://shbox.com/page/index.html
__________________
93Z M6 Black: The 385 Lives! Supercharged, 3-core front mount intercooler, GTP heads, 3:73's, Street twin clutch, Jethot Longtubes, Mufflex 4" catback/spintech, S+W cage, Spohn Suspenion, Yada Yada Yada
1) Build it
2) Race it
3) Break it
4) Repeat!!!
|
|
|
01-05-2011, 01:03 PM
|
#10
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,150
|
just trigger the oe relay.
if you want to go true standalone then figure out how to work a fan switch off the engine. you can still do a manual switch but it would be far less hackish and more effective. Is this a single fan or dual fans? I don't know v6 cars. If it is dual fan there is a cool oe bmw switch out there you can do 2 speeds with, using 2 or 3 relays.
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
01-30-2011, 03:34 PM
|
#11
|
Join Date: Jan 2008
Location: Aberdeen,nc/columbus,nj
Posts: 1,449
|
just updated the first post any info would be helpful. have this pretty much squared away but need to know where to tap into the last 2 wires.
__________________
Eric
07 Silverado 1500 5.3
01 Z28 6 speed
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|