![Reply](http://www.njfboa.org/forums/images/buttons/reply.gif) |
|
05-13-2012, 08:51 PM
|
#1
|
Join Date: Dec 2005
Location: Toms River, NJ
Posts: 350
|
my new project 91 z28 hardtop
i always wanted a blue hardtop 91-92 camaro or trans am and i found this one so i jumped on it since it was in my price range,
its a 305 tpi auto,
work to due,
sending unit bad gas tank was cut to get it out to due the fuel pump so i am going to replace the sending unit, gas tank and fuel pump, rear is out replacing with a posi 277 disc 9 bolt, [ i know crappy gears but its a parkway car] also doing all spohn upgrades lower control arms and pan hard bar, also doing the sway bars front and rear, tokico shock and struts, spohn upper strut mounts, 1LE front brake swap, borla cat back, new fuel injectors, custom valve covers, slp runners [ polished ] modded plenum [ also polished ] modded stock tb, edelbrock water pump, goodyear high milage hoses, might due the rad not sure yet, most of these parts i have had for years just sitting in the garage, time to put them to good use,
also doing a compete interior swap to black, have it all just hanging arround with some custom touches even got a set of custom rims to go on the car,
its under the knife now up on jack stands, rear out, shocks and sway bar out, front struts and strut mounts out, decided to due the lower balljoints since i am in there anyway,
this week i plan on getting the gastank out and the new tank up and in and the rear back under the car, with the exhaust up but not welded in
got pics but not able to post,
|
|
|
05-13-2012, 09:04 PM
|
#2
|
Join Date: Apr 2006
Location: Landing, NJ
Posts: 1,042
|
oh boy, ill be rooting for ya teddy, if need be make that thing rollorable and bring it up north and ill have it running.
__________________
87 Trans Am 5.7, Auto, posi disc rear, flowmaster muffler, all org car.
88 Iroc-Z TPI, Cammed 350, Vortex Heads, Magnaflow, T5, 4 Wheel Disc, 3.27 9 Bolt PBR.
91 Trans Am VertTPI 350. 700r4, K&N Air Cone, Ryven Muffler.
Last edited by ZeroCool8891; 05-13-2012 at 09:06 PM.
|
|
|
05-13-2012, 09:21 PM
|
#3
|
Join Date: Feb 2005
Location: west orange nj
Posts: 2,415
|
ted bring it up to the jew and he will finish it for you
|
|
|
05-13-2012, 10:58 PM
|
#4
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
ted email me the pics. I'll host them
Quote:
Originally Posted by chrisfrom nj
ted bring it up to the jew and he will finish it for you
|
Yeah but then he will have to buy it lol
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
Last edited by greenformula92; 05-13-2012 at 11:03 PM.
|
|
|
05-14-2012, 05:19 AM
|
#5
|
Join Date: Dec 2005
Location: Toms River, NJ
Posts: 350
|
thanks dave i know you can get it done in 2 days but i started this mess i am going to finnish it all i needs is a couple parts and about 1 week as long as there is no rain i should be able to get it drivable,
i will send some pics your way mike
|
|
|
05-16-2012, 08:37 AM
|
#6
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
wheres the pics ted?
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
|
|
|
05-16-2012, 02:52 PM
|
#7
|
11 Second Club
Join Date: Feb 2006
Posts: 932
|
Pics or you didn't do it!
__________________
2004 GTO GMM shifter Spohn stuff, tint and my love......
1988 Camaro Vert -Sold
|
|
|
05-26-2012, 09:11 PM
|
#8
|
Join Date: Dec 2005
Location: Toms River, NJ
Posts: 350
|
got some work done over the last couple days complete moog steering set up in, spohn adjustustment sleeves, tds wonder bar, need to put the new spohn sway bar in the front and swap out the old one, that will complete the front end just need to align it
well theres good news and bad news
bad news car fell and did some damage to the underside bent driveshaft smashed torque arm into floor board, but as it fell it landed on the only cinderblack i have bending the bottom of the driver fender, crushing in the rocker, as well as rear ground effect it landed on the rear that was out of the car,
good news wife pulled me away before it fell on me and my daughter
more good news car has all new lines under it, gas tank with all new guts, sending unit , fuel pump, strainer and the pusater valve, borla cat back, spohn lower control arms, and a big thanks to greenformula92 with the modivation and help in moving it along,
tomorrow, rear in, rear shocks in, gas in gas tank, spohn trans mount and torque arm set up in, spohn rear sway bar, might need to get a trans mount not sure if the old one made it or not, before i have the exhaust welded up going to get the subframes welded in first at thebodyshop also going to have them fix the floor and pull the rocker back out, also going to remove the rest of the interior, carpet, center console, rear seats and plastics, hope to have up and running all drivable with in the next week or so,
i have 2 different sets of wheels and i can t make my mind up on them,
Last edited by ted gerlach; 05-26-2012 at 09:14 PM.
|
|
|
05-27-2012, 08:23 AM
|
#9
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
to make matters worse on the wheels they are both make the car look absolutely amazing.
I was over there yesterday and we got alot done in a small amount of time, we only got to spend about 3 hours on the car so today once I head back over we can get the car on the ground and then I WILL take the pics since someone hasn't sent them to me yet haha
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
|
|
|
05-27-2012, 10:41 AM
|
#10
|
Join Date: Apr 2006
Location: Landing, NJ
Posts: 1,042
|
done yet.
__________________
87 Trans Am 5.7, Auto, posi disc rear, flowmaster muffler, all org car.
88 Iroc-Z TPI, Cammed 350, Vortex Heads, Magnaflow, T5, 4 Wheel Disc, 3.27 9 Bolt PBR.
91 Trans Am VertTPI 350. 700r4, K&N Air Cone, Ryven Muffler.
|
|
|
05-27-2012, 10:47 AM
|
#11
|
12 Second Club
Join Date: May 2005
Location: clifton nj
Posts: 236
|
pics ?
__________________
![](image.php?s=96b195cc2d611eb04f0e3b534e0edf3e&u=1356&type=sigpic&dateline=1291848270)
67 Camaro RS
70 Camaro RS
95 Camaro Z28
|
|
|
05-27-2012, 08:26 PM
|
#12
|
Join Date: Dec 2005
Location: Toms River, NJ
Posts: 350
|
mike took some today so they will be up soon,
got the rear in, forgot about the heat shields, put them back in, shocks in, old rear sway bar off new one out and under car ready to go in tomorrow, driveshaft in, spohn torque arm in, need to adjust the adjustible pan hard bar, need to bring the rear 1/2 inch to the left, have 10 inch wide rims on the back want to center them,
still need to but a poly trans mount, as well as the new pads and rotors, also going to get all new flexable brake lines, and new lines for the rear axle,
get that stuff done, send car out to get aligned, then we will go to the bodyshop for the minor opps work and both set of subframes in, then bring over to the muffler shop to weld up the exhaust all i need is a seat and seatbelts to drive it,
next thing to tackle is under the hood goodies, still need to find a set of headers would like to due before i go to have the exhaust welded,
|
|
|
05-28-2012, 09:42 AM
|
#13
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
|
|
|
05-28-2012, 09:48 AM
|
#14
|
Join Date: Apr 2006
Location: Landing, NJ
Posts: 1,042
|
ahhhh man thats some hottness rite there.
__________________
87 Trans Am 5.7, Auto, posi disc rear, flowmaster muffler, all org car.
88 Iroc-Z TPI, Cammed 350, Vortex Heads, Magnaflow, T5, 4 Wheel Disc, 3.27 9 Bolt PBR.
91 Trans Am VertTPI 350. 700r4, K&N Air Cone, Ryven Muffler.
|
|
|
05-28-2012, 09:50 AM
|
#15
|
Join Date: Feb 2010
Location: Bucks County PA
Posts: 152
|
Lookin good!
|
|
|
05-28-2012, 12:34 PM
|
#16
|
12 Second Club
Join Date: Aug 2004
Location: Oradell
Posts: 8,368
|
dammm nice rims
__________________
86 Camaro
88 Camaro
95 Impala SS
97 Trans Am WS6
98 Blazer ZR2
00 Corvette
04 CTS-V
07 Sublime Charger Daytona
10 Tahoe SSV
12 Tahoe LT
17 Malibu LT
|
|
|
05-28-2012, 07:27 PM
|
#17
|
Join Date: Oct 2009
Location: West Milford
Posts: 1,026
|
I still say you should sell me those rims ted.
|
|
|
05-28-2012, 07:52 PM
|
#18
|
Power Member
Join Date: Jul 2006
Location: Old Bridge, NJ
Posts: 2,415
|
sweet
|
|
|
05-29-2012, 05:57 AM
|
#19
|
Join Date: Dec 2010
Location: Hillsborough
Posts: 956
|
I love the color, nice car. Is that a 4th gen rear because those back tires stick out a lot...
__________________
"Quality means doing it right when no one is looking."
- Henry F*rd
|
|
|
05-29-2012, 07:28 AM
|
#20
|
Join Date: May 2010
Location: Brick, NJ
Posts: 1,868
|
Quote:
Originally Posted by 88WS-6
I love the color, nice car. Is that a 4th gen rear because those back tires stick out a lot...
|
It has a adjustable panhard rod that hasnt been adjusted yet. It needs to go about a 1/2 inch - 1 inch to the drivers side
__________________
Formerly known as blk95formula
86t/a_ram_air on TGO
2018 Silverado 1500
|
|
|
05-29-2012, 08:11 AM
|
#21
|
Join Date: Feb 2005
Location: west orange nj
Posts: 2,415
|
the car looks great ted
|
|
|
05-29-2012, 01:26 PM
|
#22
|
Join Date: May 2012
Location: Bridgewater, NJ
Posts: 835
|
Looking good!
__________________
1984 Camaro: 350 Auto, Global West Suspension, Baer Brakes, CTW Wheels
1989 GTA: Bolt-on L98. Global West Suspension, full Magnaflow exhaust, Wilwood Brakes, CTW Wheels
|
|
|
05-29-2012, 01:30 PM
|
#23
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,149
|
Nice. I recognize Ted's house of f-bodies lol
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
05-29-2012, 04:28 PM
|
#24
|
Join Date: Dec 2005
Location: Toms River, NJ
Posts: 350
|
thanks guys, its been a long time comming
had most of the parts and the wheels long before i found the car
traded parts i did not need for some parts i wanted as well
as far as the wheels go need a magic # in order to sell them,
just ordered, stainless rear axle brake lines, cross drilled and slotted rotors, and brake pads, stainless braided brake hoses,
thinking about custom dyno don headers with 3 inch y-pipe, but not going to use the borla cat back i have going to do something different
Last edited by ted gerlach; 06-02-2012 at 08:42 PM.
|
|
|
05-30-2012, 06:40 PM
|
#25
|
Join Date: Jul 2009
Location: North Jersey
Posts: 464
|
GO MAN GO !!!!!!!!!!
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|