Today's Posts Mark Forums Read Calendar
Go Back   NJFBOA - Home of New Jersey's Camaros and Firebirds > Tech Forums > Transmission and Driveline

Notices


Reply
 
Thread Tools
Old 08-26-2015, 09:53 PM   #1
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

third gen t56 swap, pressure plate issue

ok so... T56 swap is done in the car when i press the clutch the clutch fork hits the front of the pressure plate. how i know? grinding noise, and the pressure plate was painted now its not.

things to note:
factory 5 speed car (1986) so using stock pedals
new AC-delco master/slave set up
LT1 t56 (shifts gears fine)
GM lt1 flywheel, this is a 1pc rear seal SBC so this should be ok
ebay clutch
http://www.ebay.com/itm/150879006557...%3AMEBIDX%3AIT

any ideas?
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge
redsoxsstink is offline   Reply With Quote
Old 08-27-2015, 06:55 AM   #2
V
Stalker
 
V's Avatar
 
Join Date: Aug 2004
Posts: 12,077
iTrader: (12)
fork bent? or not properly inserted into TO bearing? disc not in backwards?

Last edited by V; 08-27-2015 at 07:00 AM.
V is offline   Reply With Quote
Old 08-27-2015, 07:55 AM   #3
FlyingDutchman
 
FlyingDutchman's Avatar
 
Join Date: Dec 2008
Location: NNJ
Posts: 1,489
iTrader: (1)
Social Networks:

What bellhousing are you using? Maybe it doesn't matter but if the flywheel/PP assembly is fixed to the motor and the clutch fork is fixed to the trans, maybe clearance issue? Can you see what part of the fork is touching the PP?
__________________
1997 Camaro Z28 - 355 LT1, T56, CC503, LTs, ORY, Bald Eagle-back exhaust, !emissions, Lingenfelter CAI, EWP, !CAGS, BMR LCAs, UMI PHB, Koni Str.t/Koni SA, C5 Z06 front / LS1 F-body rear brake swap, factory hurst with short stick

2014 2LT Cruze 2.0 Turbo Diesel
FlyingDutchman is offline   Reply With Quote
Old 08-27-2015, 08:14 AM   #4
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

yes i can see where the fork is touching the pressure plate, should have gotten a pic, i can do that later.
the bellhousing is the stock LT1 bellhousing.
as far as i know the fork is not bent and is properly inserted on the throw out bearing, and clutch disc is properly installed (my father helped with the fork bc i couldnt figure it out, ASE master tech at chevy)

from my research it seems like this issue is fairly common and there is no rhyme or reason and multiple ways to fix it. grind the clutch fork, let it clearance itself, use 4th gen pedals, shorten the master cylinder push rod, build a stop into the third gen pedals.
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge

Last edited by redsoxsstink; 08-27-2015 at 08:18 AM.
redsoxsstink is offline   Reply With Quote
Old 08-27-2015, 08:45 AM   #5
WildBillyT
Ayatollah of Rock N Rolla / Admin
 
WildBillyT's Avatar
 
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
iTrader: (10)
I wonder if it's a stock pedal issue. Sounds like it may be fork geometry.

I would not let this clearance itself.
WildBillyT is offline   Reply With Quote
Old 08-27-2015, 08:54 AM   #6
FlyingDutchman
 
FlyingDutchman's Avatar
 
Join Date: Dec 2008
Location: NNJ
Posts: 1,489
iTrader: (1)
Social Networks:

I was going to say maybe the 3rd gen pedals with LT1 master/slave is causing the fork to over extend and rub. I would certainly fix it right by either swapping pedals or making a stop for your 3rd gen pedals as opposed to letting it grind away your fork!
__________________
1997 Camaro Z28 - 355 LT1, T56, CC503, LTs, ORY, Bald Eagle-back exhaust, !emissions, Lingenfelter CAI, EWP, !CAGS, BMR LCAs, UMI PHB, Koni Str.t/Koni SA, C5 Z06 front / LS1 F-body rear brake swap, factory hurst with short stick

2014 2LT Cruze 2.0 Turbo Diesel
FlyingDutchman is offline   Reply With Quote
Old 08-27-2015, 09:12 AM   #7
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

i probably agree it is a geometry issue, like i said it seems to be a hit or miss issue that not everyone has. i think im gonna make a stop.

some people cut and thread that master, but i think this is sketchy. what if it breaks? now im stranded, atleast if the stop breaks i can baby it home
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge
redsoxsstink is offline   Reply With Quote
Old 08-27-2015, 10:32 AM   #8
WildBillyT
Ayatollah of Rock N Rolla / Admin
 
WildBillyT's Avatar
 
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
iTrader: (10)
Quote:
Originally Posted by redsoxsstink View Post
i probably agree it is a geometry issue, like i said it seems to be a hit or miss issue that not everyone has. i think im gonna make a stop.

some people cut and thread that master, but i think this is sketchy. what if it breaks? now im stranded, atleast if the stop breaks i can baby it home
Huh. To me that's not a bad solution as long as you get proper jam nuts and such.

My mechanical linkage is all threaded rod and rod ends and it's been perfect.
WildBillyT is offline   Reply With Quote
Old 08-27-2015, 10:36 AM   #9
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

i suppose it wouldnt be bad with the proper hardware like you said, idk in my head it just doesnt look right. i also really dont want to have to yank the master/slave back out since that requires removing the brake booster which was a major PITA for me. id love not to ever have to crawl under my dash again.
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge
redsoxsstink is offline   Reply With Quote
Old 08-27-2015, 10:47 AM   #10
ar0ck
Resident Camera Guy
 
ar0ck's Avatar
 
Join Date: Aug 2004
Location: North Jersey
Posts: 10,971
iTrader: (2)
Social Networks:

I do have a set of 4th gens Manual pedals if you decide to change your mind, I believe they need to be modified though to fit in a 3rd Gen.
__________________
ar0ck is offline   Reply With Quote
Old 08-27-2015, 11:27 AM   #11
WildBillyT
Ayatollah of Rock N Rolla / Admin
 
WildBillyT's Avatar
 
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
iTrader: (10)
Quote:
Originally Posted by redsoxsstink View Post
i suppose it wouldnt be bad with the proper hardware like you said, idk in my head it just doesnt look right. i also really dont want to have to yank the master/slave back out since that requires removing the brake booster which was a major PITA for me. id love not to ever have to crawl under my dash again.
Then go for the stop, just make it something really positive that won't give or break. If you have to pull the trans out later maybe look into the master mod.
WildBillyT is offline   Reply With Quote
Old 08-28-2015, 11:06 AM   #12
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

decided im just gonna cut and thread the rod

correct me if im wrong, maybe im overthinking this. by shortening the rod this will reduce the amount of fluid traveling to the slave but also changing the overall position of the clutch pedal when my foot is not pressing it, this is what i want.

for some reason in my head im thinking this will just change where the clutch grabs and not change how much fluid is displaced.
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge
redsoxsstink is offline   Reply With Quote
Old 08-28-2015, 12:48 PM   #13
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
iTrader: (12)
Aren't you shortening the throw? Same fluid pushing, different length rod, less disengagement, no fork to pressure plate.
__________________
sweetbmxrider is offline   Reply With Quote
Old 08-28-2015, 12:55 PM   #14
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

yes shortening the rod, so it shouldn't displace as much fluid as the longer one, fixing my issue
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge
redsoxsstink is offline   Reply With Quote
Old 08-28-2015, 01:34 PM   #15
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
iTrader: (12)
You are shortening the reach of the rod. I don't see how this would effect the fluid? I must be misunderstanding.
__________________
sweetbmxrider is offline   Reply With Quote
Old 08-28-2015, 01:48 PM   #16
NJSPEEDER
NJFBOA Co-Founder
 
NJSPEEDER's Avatar
 
Join Date: Jul 2004
Location: All up in your kool aid!
Posts: 12,235
iTrader: (10)
Shorter rod would mean lower resting height for pedal, so less throw from resting height to pedal stop.
__________________
Tim - NJSPEEDER
Currently F-bodyless

New Jersey F-Body Owners Association
NJSPEEDER is offline   Reply With Quote
Old 08-28-2015, 04:06 PM   #17
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

i want to shorten the rod so when i push the pedal down it displaces less fluid compaired to the long rod thus fixing my issue of the slave over-extending causing the fork to contact the pressure plate.

is this wrong and all im actually doing is adjusting the height of the pedal?
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge
redsoxsstink is offline   Reply With Quote
Old 08-29-2015, 02:03 PM   #18
redsoxsstink
 
Join Date: Dec 2009
Location: milltown
Posts: 1,497
iTrader: (2)
Social Networks:

so i threaded and shortened the rod for the master. it works flawlessly now. trans shifts great and clutch grabs good.

heres some pics of the contact the fork was making with the pressure plate and another of the master mod
Attached Images
File Type: jpg IMAG0490.jpg (91.8 KB, 16 views)
File Type: jpg IMAG0487.jpg (104.0 KB, 18 views)
__________________
2002 Camaro Sunset Orange Mettalic, V6, 5spd, bilstein HD shocks and struts, eibach pro lowering kit, eibach f/r sway bars, lakewood PHB, UMI 2 point subframe connectors, energy suspensions poly master bushing kit
daily econobox and first car

1986 IROC-Z, T56, MGW shifter, Heads, Cam, Holley Stealth Ram 350, t-top, tubular LCA with relo brackets, adjustable PHB, belltech sway bars, ground control weight jacks, SLP mid length headers, 3in w/borla XR1, RIP 3 10 bolts, 12.7 @ 109 so far.. atleast its faster than stock SOLD

1971 Camaro LS3/T56/9in, cam only and still carbed, RIP 2 10 bolts, 11.62@121

03 Blazer 2 door - salt sponge

Last edited by redsoxsstink; 08-29-2015 at 02:03 PM.
redsoxsstink is offline   Reply With Quote
Old 08-30-2015, 08:06 AM   #19
sweetbmxrider
Meet Coordinator
 
sweetbmxrider's Avatar
 
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
iTrader: (12)
Glad it works, however it works
__________________
sweetbmxrider is offline   Reply With Quote
Old 09-24-2015, 10:29 PM   #20
L695speed
 
L695speed's Avatar
 
Join Date: Apr 2009
Location: Andover, NJ
Posts: 777
iTrader: (0)
I was gonna chime in, but got real busy before I saw this thread. With the third gen pedals it is a hydraulics issue. Too much fluid moving, too much fork movement. Most people do what is done here, thread and make the rod adjustable. I went a different route, and used a Cavalier Z24 slave cylinder, with a LT1 T56 master. Third gen pedals. I have progressive engagement, with full engagement at maybe a couple inches from the floor.

On another note, the fourth gen pedals will work, but, and be warned, people have reported cracking firewalls because they don't bolt in like the stock third gen ones do. Some of the holes do NOT line up, particularly the one going into the upper cowl. Use the third gen pedals, they're not exactly rare, and they bolt into the car properly.
L695speed is offline   Reply With Quote
Reply

  NJFBOA - Home of New Jersey's Camaros and Firebirds > Tech Forums > Transmission and Driveline


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Sponsor List














All times are GMT -5. The time now is 07:29 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.