 |
09-11-2018, 09:48 AM
|
#1
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
engine balancing
So my motor is a mix of factory parts, ls2 rods and pistons, lq4 crank in an lq9 block. Does all this need to be re-balanced or should it be good since its all factory stuff?
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
09-11-2018, 10:38 AM
|
#2
|
Join Date: Nov 2007
Location: Jackson, NJ
Posts: 1,724
|
Has this already been put together and run? Or is this a new build?
If it is a new build, its cheap insurance to have all the parts looked at by the machine shop and re-balanced as needed.
__________________
1983 camaro- Scrap
1988 camaro- Also scrap
'05 Silverado- You guessed it, scrap
1988 TRX 250R- Ported w/ high compression on 110 octane- Out 60' your LT1
Jersey Shore Street Car Takeover (JSSCT) Founder
Quote:
Originally Posted by LS1ow
and once i get PHB, what do i ajust it too?
|
Quote:
Originally Posted by Jersey Mike
Seven.
|
|
|
|
|
|
09-11-2018, 10:57 AM
|
#3
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
New build. Used parts obviously. Block was hot tanked, checked, honed, and assembled. Guy I bought it off of sold his car then sold the motor fresh from the machine shop.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
|
09-11-2018, 11:04 AM
|
#4
|
|
Ayatollah of Rock N Rolla / Admin
Join Date: Mar 2006
Location: Parts Unknown
Posts: 12,573
|
If the rotating assembly is made up of used parts from different engines I would say you absolutely have to get it checked/modified.
|
|
|
|
|
09-11-2018, 12:11 PM
|
#5
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
Hum, ok. That's what I was worried about. The guy never mentioned having it balanced when I bought it. I'll have it checked out.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
|
09-11-2018, 12:28 PM
|
#6
|
|
Lord of the rings / 10 Second Club / Meet Coordinator
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,361
|
I'd have it balanced.
__________________
97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140
'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
|
|
|
|
|
09-11-2018, 12:56 PM
|
#7
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,152
|
Don't cheap our, do it!
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
|
09-11-2018, 06:46 PM
|
#8
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,341
|
Definitely needs to be balanced. You didn't mention internal or external either but the mix up needs to be balanced together. A factory rotating assembly staying together is different.
|
|
|
|
|
09-11-2018, 06:52 PM
|
#9
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
Quote:
Originally Posted by sweetbmxrider
Definitely needs to be balanced. You didn't mention internal or external either but the mix up needs to be balanced together. A factory rotating assembly staying together is different.
|
I just assumed all ls were internal. So whatever a stock lq4 crank and ls2 rods require balance wise.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
|
09-11-2018, 06:53 PM
|
#10
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,152
|
your engine guy will know all the questions & answers.
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
|
09-11-2018, 07:50 PM
|
#11
|
|
American Road Warrior
Join Date: Jul 2005
Location: Wastelands of NJ
Posts: 6,116
|
How many cubic inches will this engine be?
__________________
unstable bob gable: LEGENDARY LEGEND,
ICONIC ICON, AND AMERICAN BAD AZZ!!!
1991 Dodge Spirit R/T: Gran'pa lookin' 150+ mph turbo rocket.
2013 Dodge Avenger RT: Wastelands cruiser.
2008 Crown Vic Police Interceptor: 'Nuff said!
THE ONLY THING THAT SUCKS WORSE THEN IMPORTS ARE RICED OUT IMPORTS!!!
|
|
|
|
|
09-11-2018, 08:08 PM
|
#12
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
364, stock 6.0l size.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
|
09-11-2018, 08:08 PM
|
#13
|
|
American Road Warrior
Join Date: Jul 2005
Location: Wastelands of NJ
Posts: 6,116
|
Quote:
Originally Posted by B4C
364, stock 6.0l size.
|
Cool.
__________________
unstable bob gable: LEGENDARY LEGEND,
ICONIC ICON, AND AMERICAN BAD AZZ!!!
1991 Dodge Spirit R/T: Gran'pa lookin' 150+ mph turbo rocket.
2013 Dodge Avenger RT: Wastelands cruiser.
2008 Crown Vic Police Interceptor: 'Nuff said!
THE ONLY THING THAT SUCKS WORSE THEN IMPORTS ARE RICED OUT IMPORTS!!!
|
|
|
|
|
09-11-2018, 08:43 PM
|
#14
|
Join Date: Jun 2016
Location: Millstone
Posts: 142
|
Def balance
|
|
|
|
|
09-12-2018, 02:55 PM
|
#15
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
Getting dropped off next time I visit my parents in Jersey since the machine shop I want to use is only a town over from them. After talking to them on the phone it definitely needs to get balanced lol.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
|
09-12-2018, 04:15 PM
|
#16
|
|
Lord of the rings / 10 Second Club / Meet Coordinator
Join Date: Aug 2004
Location: Millstone Township, NJ
Posts: 6,361
|
Quote:
Originally Posted by B4C
Getting dropped off next time I visit my parents in Jersey since the machine shop I want to use is only a town over from them. After talking to them on the phone it definitely needs to get balanced lol.
|
You doubted all of our knowledge?!?!?
__________________
97 T/A Ram Air Convt
Forever dyno queen / 777rwhp 662 rwtq @ 17lbs / 10.2 @ 140
'24 Corvette Z06
17 Sierra 2500HD Dmax
81 Turbo TA
|
|
|
|
|
09-12-2018, 04:57 PM
|
#17
|
Join Date: May 2007
Location: Jim Thorpe PA
Posts: 2,133
|
Quote:
Originally Posted by Blackbirdws6
You doubted all of our knowledge?!?!?
|
No, but I doubt his knowledge less lol.
__________________
01 SS 383 stroker, Magnum F, 9in.
86 Trans-Am 355 t56
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
