|
08-11-2012, 06:25 PM
|
#1
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
reinstalled harness after cleaning up hacked up mess, not gettin spark
i just cleaned up my harness and removed all the crimp connectors and soldered everything nice and neat and reinstalled it, and i am now not getting any spark. no power to the icm, i cant figure out what it could be. did i forget to connect a ground? did i mess up some wires? please help. need to get this fixed asap so i can finally drive this monster.
__________________
|
|
|
08-12-2012, 07:10 PM
|
#2
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
So the pink wire feeding the coil has no power?
Ignition wise, everything is plugged in correctly?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
08-13-2012, 06:10 PM
|
#3
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
Quote:
Originally Posted by LTb1ow
So the pink wire feeding the coil has no power?
Ignition wise, everything is plugged in correctly?
|
i will check in a few mins about that pink wire, but one of the red wires going to the opti has power. which ones should have power with key on? and when cranking?
__________________
|
|
|
08-13-2012, 07:00 PM
|
#4
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
Quote:
Originally Posted by Coreylt1
i will check in a few mins about that pink wire, but one of the red wires going to the opti has power. which ones should have power with key on? and when cranking?
|
no power to the coil. no power to the icm.
__________________
|
|
|
08-13-2012, 07:01 PM
|
#5
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
Did you check your ignition fuse?
Edit: Should be fuse 11 I think
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
Last edited by LTb1ow; 08-13-2012 at 07:03 PM.
|
|
|
08-13-2012, 07:10 PM
|
#6
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
Quote:
Originally Posted by LTb1ow
Did you check your ignition fuse?
Edit: Should be fuse 11 I think
|
yes
__________________
|
|
|
08-13-2012, 07:15 PM
|
#7
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
Ok, well check to make sure you have power leaving that fuse, if so, you have a break somewhere. That fuse feeds the coil, ICM, and CPS.
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
Last edited by LTb1ow; 08-13-2012 at 07:15 PM.
|
|
|
08-13-2012, 10:30 PM
|
#8
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
Quote:
Originally Posted by LTb1ow
Ok, well check to make sure you have power leaving that fuse, if so, you have a break somewhere. That fuse feeds the coil, ICM, and CPS.
|
so i tested the opti harness and the icm. the grounds ohm'd bad, so i made new ones. no luck.
__________________
|
|
|
08-13-2012, 10:35 PM
|
#9
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
Quote:
Originally Posted by Coreylt1
so i tested the opti harness and the icm. the grounds ohm'd bad, so i made new ones. no luck.
|
do i need to have a ground to the block? i have the ground strap connected from the frame to the block, but is it necessary to have grounds connected to the block or should i be able to attach them anywhere to a good clean ground
__________________
|
|
|
08-14-2012, 07:16 AM
|
#10
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,900
|
From what I remember there are a few grounds at the head on an ICM stud, and then the ground strap to the frame from there. There is also a PCM ground on the passenger side of the block near the knock sensor.
Do you have voltage at the fuse and after it?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
08-14-2012, 09:42 PM
|
#11
|
Join Date: Jan 2012
Location: north jersey!
Posts: 87
|
Quote:
Originally Posted by LTb1ow
From what I remember there are a few grounds at the head on an ICM stud, and then the ground strap to the frame from there. There is also a PCM ground on the passenger side of the block near the knock sensor.
Do you have voltage at the fuse and after it?
|
will check the fuse tomorrow, forgot.
i did check the yellow wire on the opti harness, pin B . should be 2-4 volts when cranking. it was bouncing around but didnt go over 2.2 volts
__________________
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|