WTB: 350 parts. - NJFBOA - Home of New Jersey's Camaros and Firebirds

Blackwizard222 · 05-13-2005, 07:40 PM

Looking for parts for a 350 small block:
Performance hydraulic flat cam
Performance Intake manifold
Performance heads
Holley carb
Long tubes for an el camino (1979)
Rear end out of a monte carlo or el camino with 3.73 gears
Stall vert for th350.

List what ya got and how much u want!

9secfirebird · 05-13-2005, 10:37 PM

i have an intake manifold. weiand Xcellerator. it looks great and is a real powerful unit. 55.00 would be good, its got very very low miles on it and looks awesome lemme know if your interested! i have ATON of small block **** sittin around my houselemme know what else you might need.

NJSPEEDER · 05-14-2005, 11:33 AM

a clearer definition of "performance" would be good.
i have a few blocks that would be good for rebuild, iron eagle heads that will work in you wanna spin it to 6500rpm or so, a few intake ranging from a performer rpm to a tunnel ram.
i also have a 400sbc 4bolt block, a spare 350 crank and rod set, and other misc. stuff around.

later
tim

Blackwizard222 · 05-14-2005, 12:01 PM

Well, strip/street stuff, its goin on a 1979 el camino thats registered QQ.

The short block is done, i just am looking for top end parts:
Heads
Single plane intakes
Holley carbs
Cams
Gear drive
Headers
Flowmaster mufflers
ETC...

The car has a performer on it now so if u got any single planes let me know.

9secfirebird · 05-14-2005, 01:34 PM

my weiand is a single plain!!!!!

Blackwizard222 · 05-15-2005, 07:45 PM

ok well im peicing together what i want and such. if i decide i want it ill be sure to email you.

9secfirebird · 05-15-2005, 10:02 PM

i have a nice 7 second motor for ya

only 4,000 and its yours its a short block but its a steal at that price.

bad64chevelle · 05-15-2005, 10:20 PM

Hey 9 second...happen to have an oil bypass valve for a 327?

NJSPEEDER · 05-15-2005, 10:23 PM

9secbirds weiand intake and my iron eagle heads would make the basis of a nice combo

grab a cam so that you can shift at 6500-7000rpm and you would be flying.

later
tim

Blackwizard222 · 05-16-2005, 01:17 AM

what do u want for the heads? what r the specs on them? im not planning on going much bigger than comp cams 270h magnum. gear 3.73 and mininal stall.

Slow Z · 05-16-2005, 11:43 AM

Hey my friend has an 8.5" GN rear with driveshaft he'd probably sell ya.. All fresh parts.

Slow Z · 05-16-2005, 11:44 AM

Quote:

Originally Posted by 9secfirebird

i have a nice 7 second motor for ya

only 4,000 and its yours its a short block but its a steal at that price.

7 second? in what the 1/8th?

9secfirebird · 05-16-2005, 03:47 PM

do everyone a favor and only ask a question about the item or respond to the item if you are seriously considering it. if your not, dont waste everyones time and bandwith.

Blackwizard222 · 05-16-2005, 11:14 PM

*EDIT*

Tru2Chevy · 05-17-2005, 09:12 AM

Quote:

Originally Posted by Blackwizard222

just because i havent responded to you in a split second with a decision doesnt mean im not considering it. Â*But **** with that kinda attitude i doubt ull sell anything.

Learn to have patience.

I think 9sec's comment was directed at Slow Z, not you.

- Justin

9secfirebird · 05-17-2005, 11:12 AM

yes it was. thanks justin.

Slow Z · 05-17-2005, 11:37 AM

That was a serious question... Lets see a motor that goes 7.999 in a 3000lb car would be making around 1200HP... Now a SBC shortblock that'll handle over 1200HP would look something like this:

Dart Little M block w/ billet caps: $2100
Callies 4340 Dragon Slayer Crank: $800
Oliver Billet rods: $1300
JE Pro Series pistons: $800
All other goodies + machine work: $1000
Total: Atleast $6000, probably consideribly more.

So if you have a shortblock like that and you want $4000 I might have you a buyer.

Blackwizard222 · 05-17-2005, 12:00 PM

Quote:

Originally Posted by 9secfirebird

yes it was. thanks justin.

Oh my bad.

Tru2Chevy · 05-17-2005, 01:34 PM

Please take further discussion of the $4,000 shortblock in question here:

http://www.njfboa.org/forums/viewtopic.php?t=3515

Thanks guys.

- Justin

9secfirebird · 05-17-2005, 08:18 PM

slowZ - click on the link in the above thread, my response is there

Blackwizard222 · 05-17-2005, 10:27 PM

ok

we got a stall converter, cam, and headers already.

I want your manifold 9sec.

So that leaves me needing a set of heads with 64cc chambers and at least 1.94/1.50 valves. Not looking for aftermarket heads (too much $$$).

Also need a set of dumped flowmasters

Rear end with 3.73 posi for a G body

Mike · 05-17-2005, 10:53 PM

lol didnt herman tell you to ask me about elcamino parts?.........ill ask my dad tomorow to see what he has laying around.

Blackwizard222 · 05-17-2005, 11:18 PM

Quote:

Originally Posted by Slow Z

Hey my friend has an 8.5" GN rear with driveshaft he'd probably sell ya.. All fresh parts.

what kinda gears? posi? how much?

im looking for a g body rear with 3.73 posi. monte carlo ss, gn, etc...

Blackwizard222 · 05-17-2005, 11:19 PM

Quote:

Originally Posted by cbrrmike

lol didnt herman tell you to ask me about elcamino parts?.........ill ask my dad tomorow to see what he has laying around.

no herman didnt lol. forgot u had one. let me know what u got. my dad wants a hood too, if ya still got one.

Blackwizard222 · 05-22-2005, 12:29 PM

got heads and manifold. i need a rear and thats really about it.