 |
|
10-30-2009, 12:31 PM
|
#1
|
Join Date: Nov 2007
Posts: 35
|
4L60E for Sale Cheap!!!
I have a rebuilt trans with only 50K on it for sale for $200.00 or best offer.
Last edited by ZCarr; 10-31-2009 at 06:29 PM.
|
|
|
|
11-02-2009, 02:10 AM
|
#2
|
Join Date: Aug 2008
Location: Manahawkin
Posts: 83
|
what converter?
__________________
99 Z28 Boltons 2 stages 88 Camaro 350 TBI swap
|
|
|
|
|
11-02-2009, 06:55 AM
|
#3
|
Join Date: Jul 2009
Location: barnegat nj
Posts: 1,340
|
what year is it out of?
|
|
|
|
|
11-02-2009, 11:09 AM
|
#4
|
Join Date: Nov 2007
Posts: 35
|
Stock Converter and it is out of a 1994
|
|
|
|
|
11-02-2009, 01:40 PM
|
#5
|
Join Date: Jul 2009
Location: barnegat nj
Posts: 1,340
|
you need to let people know that this is for lt1 & down cars.
your trans has a 298mm stator
the 98-02 fbody & trucks w/ ls style engine have 300mm stator
not being a dick, just tryin to help you out so you don;t get a million questions about it.
|
|
|
|
|
11-02-2009, 07:53 PM
|
#6
|
Join Date: Dec 2005
Posts: 87
|
If it will fit a 97 formula Im interested. PM me the part number.
__________________
97 Black WS6 Formula, 60k miles, M6, Forged 355 LT1Mahle Power Pack, Scat Forged Rods, LE2 Heads and Cam, 58 MM TB, 37lb Delphi Injectors, Pacesetter Race Longtubes, 3 inch cutout, Magnaflow catback, Mezire Electric WP, Taylor OVC Wires, PCM for less tune.
|
|
|
|
|
11-03-2009, 10:32 AM
|
#7
|
Join Date: Nov 2007
Posts: 35
|
I will send you the part number when I get home.
|
|
|
|
|
11-03-2009, 10:41 AM
|
#8
|
Join Date: Jul 2009
Location: barnegat nj
Posts: 1,340
|
if its out of a 93-97 lt1 car then it will fit
|
|
|
|
|
11-03-2009, 10:43 AM
|
#9
|
|
Mongo the Meet Coordinator
Join Date: May 2008
Posts: 16,941
|
Fit yes, but weren't the early years 4L60 not the later years 4L60E?
__________________
Quote:
Originally Posted by KirkEvil
repo bigals turd gen and part it out to a loving home
|
|
|
|
|
|
11-03-2009, 11:00 AM
|
#10
|
Join Date: Jul 2009
Location: barnegat nj
Posts: 1,340
|
93-97 4l60e in the fbodys are the same guts & shell
i beleive the splits are 93-94 95 & 96-97
& the differneces is the electronics which can be changed.
(remove pan, change solenoids & harness out of old one to new one.)
|
|
|
|
|
11-03-2009, 06:52 PM
|
#11
|
|
Co-Founder / Site Admin
Join Date: Jul 2004
Location: Ewing, NJ
Posts: 22,476
|
93 was 4L60, 94-97 was 4L60e
The '94 trans for sale here will fit the '97 Formula in question with no problems unless the '94 trans was for the 3.4L (since the OP didn't specify).
- Justin
__________________
1999 Camry - Beigemobile DD
2002 Suburban - Wife's DD
2004 Grand Cherokee - Not running / Project / Selling?
|
|
|
|
|
11-03-2009, 07:01 PM
|
#12
|
Join Date: Dec 2005
Posts: 87
|
Ok if it fits 97 I want it. I am sending you a PM.
__________________
97 Black WS6 Formula, 60k miles, M6, Forged 355 LT1Mahle Power Pack, Scat Forged Rods, LE2 Heads and Cam, 58 MM TB, 37lb Delphi Injectors, Pacesetter Race Longtubes, 3 inch cutout, Magnaflow catback, Mezire Electric WP, Taylor OVC Wires, PCM for less tune.
|
|
|
|
|
11-05-2009, 05:50 PM
|
#13
|
Join Date: Dec 2005
Posts: 87
|
Whats going on? You selling this or not?
__________________
97 Black WS6 Formula, 60k miles, M6, Forged 355 LT1Mahle Power Pack, Scat Forged Rods, LE2 Heads and Cam, 58 MM TB, 37lb Delphi Injectors, Pacesetter Race Longtubes, 3 inch cutout, Magnaflow catback, Mezire Electric WP, Taylor OVC Wires, PCM for less tune.
|
|
|
|
|
11-05-2009, 05:59 PM
|
#14
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,370
|
IIRC, 94 is the goofball year (typical lt1) and will only fit 94s.....
|
|
|
|
|
11-05-2009, 06:07 PM
|
#15
|
|
11 second club / Moderator
Join Date: Aug 2004
Location: West Berlin, NJ
Posts: 7,148
|
Quote:
Originally Posted by sweetbmxrider
IIRC, 94 is the goofball year (typical lt1) and will only fit 94s.....
|
HMMM? Not to my knowledge. Only 93 used a 700R4 (kickdown cable), then 94 and up used 4L60E
__________________
2001 Trans Am WS6 •SLP Loudmouth II •UMI Suspension •12.857 @ 109.57
1996 Trans Am WS6 •Pacesetter Longtubes •Strange 12 Bolt •Spohn Suspension •11.152 @ 123.85
|
|
|
|
|
11-05-2009, 06:13 PM
|
#16
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,370
|
Quote:
To put a ’96 4L60E into a ’94 car: The ’94 tailshaft housing and VSS must be installed on the ’96 4L60E before the trans can be bolted into the car. Mod A must be performed. The trans will operate normally without Mod A but TCC lockup will not work, so highway and cruising gas mileage will suffer and more heat will be produced in the transmission.
TCC Mod (method 1):
An additional wire must be run from the PCM connector D pin 6 to pin "U" on the trans harness for the TCC to work. Also, the PCM must be reprogrammed with ’95 transmission base code. In my opinion this is more work than its worth due to the amount of labor involved in properly routing an additional wire into the powertrain wiring harness.
TCC Mod (method 2):
Leave the PWM solenoid unplugged but installed. On the valve directly to the right of the PWM solenoid – push that valve all the way towards the outside of the valvebody, and stake it into place. That’ll lock keep the valve acted on by the PWM in the full-open position and it’ll function like a '94 style lockup. No PCM reprogramming required. Now with pics! You may have to swap the ’94 internal harness into '95-’96 transmission, but I'm not sure. I recommend not swapping harnesses if you don't have to, because they will most likely be brittle and are tricky to remove from the case without damaging the lugs on the connector.
|
for what its worth
"mod a"
http://www.impalassforum.com/vBullet...6&postcount=12
Last edited by sweetbmxrider; 11-05-2009 at 06:16 PM.
|
|
|
|
|
11-06-2009, 07:44 PM
|
#17
|
Join Date: Dec 2005
Posts: 87
|
Well I wanted to put it in a 97, but no matter, this guys doesnt answer PM's or update his posts. I will find another one, there are plenty out there.
__________________
97 Black WS6 Formula, 60k miles, M6, Forged 355 LT1Mahle Power Pack, Scat Forged Rods, LE2 Heads and Cam, 58 MM TB, 37lb Delphi Injectors, Pacesetter Race Longtubes, 3 inch cutout, Magnaflow catback, Mezire Electric WP, Taylor OVC Wires, PCM for less tune.
|
|
|
|
|
11-06-2009, 08:16 PM
|
#18
|
|
Meet Coordinator
Join Date: Jan 2008
Location: brick/pt. pleasant beach
Posts: 19,370
|
i would consider 97 the same as 96 in reference to that article....
|
|
|
|
|
11-10-2009, 08:28 PM
|
#19
|
Join Date: Nov 2007
Posts: 35
|
I responded to your pm. I am sorry for the delay in getting back you I had a death of a long time friend of the family.
|
|
|
|
|
11-19-2009, 01:59 PM
|
#20
|
|
Stalker
Join Date: Aug 2004
Posts: 12,083
|
do you know if id be able to put the tailhousing from a 4wd 4l60e onto this 2wd one and use it in a 96 4wd tahoe? if so im very interested
|
|
|
|
|
02-10-2010, 05:30 PM
|
#21
|
Join Date: Nov 2007
Posts: 35
|
ttt
|
|
|
|
|
02-14-2010, 07:35 AM
|
#22
|
Join Date: Feb 2008
Location: Williamstown, NJ
Posts: 191
|
Location in NJ?
__________________
1998 Mustang GT
1992 Mustang LX
|
|
|
|
|
02-14-2010, 10:17 AM
|
#23
|
Join Date: Nov 2007
Posts: 35
|
South Jersey right off of exit 2.
|
|
|
|
|
02-16-2010, 10:54 AM
|
#24
|
Join Date: Nov 2007
Posts: 35
|
ttt
|
|
|
|
|
02-16-2010, 12:40 PM
|
#25
|
Join Date: Jul 2007
Location: mullica hill
Posts: 31
|
where are you off exit 2? i live half a mile from there
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
