 |
03-03-2012, 12:32 PM
|
#1
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
rebuildable 383 fs $400 firm
the guy i bought this from did not understand how to store an engine, he left it dry and uncovered in his basement, lots of surface rust, ill get some pics up later, heres some info:
JE forged pistons(i think 10cc dish iirc)
Eagle i beam rods and crank
ARP rod and main bolts...
1pc rear main seal...
needs crank polished, rings, honed and might as well put in new bearings,
2 bolt block and complete rotating assembly
should make a pretty cheap 383 especially if u can do most of the work yourself, im moving to a house with a smaller garage and im not gonna have room to have this sitting like it is now
$400 firm, its worth it.
located in Lords Valley PA 18428 i can deliver within 100 miles for $475 cash or maybe trade for some 16" drag radials and a little cash?? also interested in a complete WCT5 swap
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
Last edited by Flippindabird; 03-03-2012 at 12:34 PM.
|
|
|
|
03-04-2012, 11:06 AM
|
#2
|
Join Date: May 2009
Location: Williamstown
Posts: 91
|
Carb or fuel injected motor
|
|
|
|
|
03-04-2012, 07:56 PM
|
#3
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
lol it doesnt have a cam.... its a 1pc rear main seal block... which were all TBI or F.I from the factory... you put whatever heads cam intake etc etc on it and make it do what u want cam choice is probably the only thing that REALLY matters as far as carb/F.I. goes
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-04-2012, 08:06 PM
|
#4
|
Join Date: May 2009
Location: Williamstown
Posts: 91
|
Can u send me the number off the block so I can see what it may have came out of thanks
|
|
|
|
|
03-04-2012, 08:14 PM
|
#5
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
def will when i get home tomorrow ill post some pics too, if i remeber correctly it came from a pass car, but the block really doesnt matter LOL what your paying for is the rotating assembly
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-04-2012, 08:16 PM
|
#6
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
btw the rotating assembly will work in your LT1, the block wont 
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-04-2012, 08:28 PM
|
#7
|
Join Date: May 2009
Location: Williamstown
Posts: 91
|
That is why I was asking but I have a 2000 Trans am now and looking to build another motor
|
|
|
|
|
03-04-2012, 09:14 PM
|
#8
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
ok... nah man youll need a "LS" motor for your 2000 t/a this is a conventional small block chevy... guess i should have stated that 
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-04-2012, 09:24 PM
|
#9
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,170
|
Quote:
Originally Posted by Flippindabird
...cam choice is probably the only thing that REALLY matters as far as carb/F.I. goes
|
mechanical fuel pump provision?
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
|
03-04-2012, 09:43 PM
|
#10
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
dont think so bonz... have to check
see your point... that would be the other thing, BUT carbs can be ran with electric pumps like the one in my car lol
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
Last edited by Flippindabird; 03-04-2012 at 09:45 PM.
|
|
|
|
|
03-04-2012, 09:49 PM
|
#11
|
|
Admin.
Join Date: Aug 2005
Location: Hamilton, NJ
Posts: 20,170
|
just saying that will matter to some buyers.
__________________
Vent Windows Forever!
The looser the waistband, the deeper the quicksand. Or so I have read.
Feather-light suspension, Konis just couldn't hold. I'm so glad I took a look inside your showroom doors.
Hey everybody, it's good to have you on the Baba-too-da-ba-too-ba-ba-buh-doo-ga-ga-bop-a-dop
|
|
|
|
|
03-04-2012, 10:11 PM
|
#12
|
Join Date: Feb 2010
Location: Stillwater
Posts: 822
|
Quote:
Originally Posted by BonzoHansen
mechanical fuel pump provision?
|
I am drawing a blank here so excuse me if I'm wrong. The newer (first gen vortec year) small blocks had provisions for mechanical fuel pumps but I can't recall if they were just castings.
__________________
Quote:
Originally Posted by LTb1ow
...its cool to like diesels, cause that and pretending to be country is like, hip nowadays!!
|
|
|
|
|
|
03-05-2012, 07:25 AM
|
#13
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
@ bonz yeah i get ya
@raffz i thought mech fuel pump provision stopped after early l98ish blocks, but i could be wroing as well, ill be home in a few hours to check
but like i said your really paying for the rotating assembly and the block is free... add your own block with fuel pump provision and your good
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-05-2012, 08:01 AM
|
#14
|
Join Date: Jun 2007
Location: Arm pit of the world... NJ
Posts: 2,677
|
Forged or cast crank? What size are the pistons?
__________________
John
|
|
|
|
|
03-05-2012, 06:48 PM
|
#15
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
pistons are .030 over "383 specific" JE pistons 10 or 12cc dish
i would not sell a forged crank for 400 with pistons and rods 
had some stuff to do during the day and now that im home i dont feel like going out to the cold garage to take pics but i will have them up tomorrow, sorry bout that.
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
Last edited by Flippindabird; 03-05-2012 at 06:50 PM.
|
|
|
|
|
03-09-2012, 07:42 PM
|
#16
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
heres a few pics... you can see the rust i was talking about
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-09-2012, 10:36 PM
|
#17
|
Join Date: Feb 2010
Location: Stillwater
Posts: 822
|
first dibs. pming you for a phone number.
__________________
Quote:
Originally Posted by LTb1ow
...its cool to like diesels, cause that and pretending to be country is like, hip nowadays!!
|
|
|
|
|
|
03-14-2012, 10:24 AM
|
#18
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
sorry everyone but ive decided to keep it unless i can get $550 delivered (
within 100 miles)
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
|
03-14-2012, 03:20 PM
|
#19
|
Join Date: Feb 2010
Location: Stillwater
Posts: 822
|
Ridiculous. He gets offered his asking price and booop! Price goes up.
__________________
Quote:
Originally Posted by LTb1ow
...its cool to like diesels, cause that and pretending to be country is like, hip nowadays!!
|
|
|
|
|
|
03-15-2012, 10:49 AM
|
#20
|
Join Date: Mar 2010
Location: The Pocono Moutains
Posts: 142
|
i explained the reason to you, and i apologized... evidently your feelings are hurt??? sorry about your luck kid, im keeping it.
__________________
run 12s with a JUNK motor!
^^^^^my new mantra^^^
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
