 |
07-31-2005, 04:01 AM
|
#1
|
Join Date: Aug 2004
Location: Toms River
Posts: 523
|
gear reclabration
hey guys im gettin a rear swap done on tues with 3:42's in it. nwo im not sure what was in my old rear but i dont think it was 3:42's so im gona need to tell how fast im goin..can ne1 do reprogram it for me like asap after i get it done? i know fasterthenyou does it but how much does it usually run aorund $ wise?
thanks guys
justin
|
|
|
|
07-31-2005, 04:09 AM
|
#2
|
|
Banned Camp Director Emeritus
Join Date: Aug 2004
Location: Somerset County
Posts: 8,395
|
I thought 93's had the 4l60, not the 4l60e. that would mean its a mechanical driven speedo. you might need a new gear. someone please correct me if I'm wrong.
__________________
Quote:
Originally Posted by baddest434
and 1 more smart ass answer by you and i'm going to reach into this monitor and grab you by the throat
|
|
|
|
|
|
07-31-2005, 05:02 AM
|
#3
|
Join Date: Sep 2004
Location: Perth Amboy,NJ
Posts: 396
|
No,your right 
Later,
Santos
|
|
|
|
|
07-31-2005, 03:57 PM
|
#4
|
Join Date: Aug 2004
Location: Toms River
Posts: 523
|
anyone know this part number or how much it costs?...how hard are they to install? im already broke from gettin everything for the rear wounder how much this disaster is gona cost lol
thanks for the help guys
justin
|
|
|
|
|
07-31-2005, 04:42 PM
|
#5
|
|
Keyboard Tough Guy
Join Date: Jul 2004
Location: Trenton, NJ
Posts: 6,341
|
they are usually $15-25 i saw it done on my mustang...took about 5 mins from what i remember.
|
|
|
|
|
07-31-2005, 05:14 PM
|
#6
|
|
13 Second Club
Join Date: Jul 2004
Location: Ewing/Galloway, NJ
Posts: 3,904
|
SLP made these calibration boxes, they stopped making them a long time ago...you may be able to pick one up for less than 100 bucks, i think fastbird had an extra he was trying to sell....if you cant find any, dakota digital makes a box, ~150 bucks iirc
__________________
EB
99 Riviera, Bone stock, 14.34 @ 96 "Walking 5.0's in luxury" RIP
95 Cherokee, Bone stock 16.2 @ 83 "Treeing your 3rd gen and beating it to the line despite trapping less....and looking better"
93 TA, Bone stock, 13.8 @ 100 "Beating ****** drivers in ****** LS1's"
https://www.facebook.com/groups/285090241699967/
R.I.P. Tia 
|
|
|
|
|
07-31-2005, 06:25 PM
|
#7
|
|
Banned Camp Director Emeritus
Join Date: Aug 2004
Location: Somerset County
Posts: 8,395
|
Quote:
|
Originally Posted by Squirrel
SLP made these calibration boxes, they stopped making them a long time ago...you may be able to pick one up for less than 100 bucks, i think fastbird had an extra he was trying to sell....if you cant find any, dakota digital makes a box, ~150 bucks iirc
|
Its not electronically controlled, I dont think the box will help 
__________________
Quote:
Originally Posted by baddest434
and 1 more smart ass answer by you and i'm going to reach into this monitor and grab you by the throat
|
|
|
|
|
|
08-02-2005, 10:43 AM
|
#8
|
|
Co-Founder / Site Admin
Join Date: Jul 2004
Location: Ewing, NJ
Posts: 22,473
|
It's sorta electrically controlled. It should have a pair of speedo gears in the tranny, but the signal is sent electronically from the trans (just like a late 3rd gen). I would assume that swaping the rear gears would be the easiest/cheapest way to do it.
- Justin
__________________
1999 Camry - Beigemobile DD
2002 Suburban - Wife's DD
2004 Grand Cherokee - Not running / Project / Selling?
|
|
|
|
|
08-02-2005, 04:21 PM
|
#9
|
Join Date: Aug 2004
Location: Montgomery NJ
Posts: 1,271
|
Quote:
|
Originally Posted by Tru2Chevy
It's sorta electrically controlled. It should have a pair of speedo gears in the tranny, but the signal is sent electronically from the trans (just like a late 3rd gen). I would assume that swaping the rear gears would be the easiest/cheapest way to do it.
- Justin
|
 Remove the driveshaft, remove the tail shaft, drain fluid out, get a new seal if you need it for the tail shaft, replace gears, and go. Total cost with gaskets was like $19 if I remember correctly. It was only $15 for the 2 gears I needed.
__________________
, Jon
Owner of a Red Sled.
If it\'s EFI I can tune it. Specialize in 82-95 GM (yes Lt1\'s)
\"If you can leave black marks on a straight from the time you exit a corner till the time you brake for the next turn.......Then, you have enough horsepower\" - Mark Donohue 
|
|
|
|
|
08-02-2005, 07:16 PM
|
#10
|
Join Date: Sep 2004
Location: Perth Amboy,NJ
Posts: 396
|
Justin,the trans in the Z have the gears calibrated for 3:73's.make sure you keep them in case you decide to swap to them in the future..
Later,
Santos
|
|
|
|
|
08-03-2005, 02:20 PM
|
#11
|
Join Date: Oct 2004
Posts: 365
|
ok, there is one bolt holding the speedo in...take the bolt out, unplug the speedo, pull the speedo out, put the new one in, but the bolt back in, plug it back in. its that simple, dont atke off the tailshaft housing and all that crap, it takes 2.5 mins and shouldnt take any less.
__________________
AIM: blacktoprecs
|
|
|
|
|
08-03-2005, 04:29 PM
|
#12
|
|
Co-Founder / Site Admin
Join Date: Jul 2004
Location: Ewing, NJ
Posts: 22,473
|
Quote:
|
Originally Posted by 9secfirebird
ok, there is one bolt holding the speedo in...take the bolt out, unplug the speedo, pull the speedo out, put the new one in, but the bolt back in, plug it back in. its that simple, dont atke off the tailshaft housing and all that crap, it takes 2.5 mins and shouldnt take any less.
|
That only works if you only have to change one of the gears. If you have to change both gears to get the desired ratio, you have to pull the tailhousing.
- Justin
__________________
1999 Camry - Beigemobile DD
2002 Suburban - Wife's DD
2004 Grand Cherokee - Not running / Project / Selling?
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
|
